Vivo life finds LF-VFS1A User manual

Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://lifefinds.store/products/lf-vfs1a
[email protected]tore www.lifefinds.store 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
Vacuum Floor Stand & Accessory Holder
Designed for Dyson Vacuums
Instruction Manual
SKU: LF-VFS1A

2
PACKAGE CONTENTS
15.6lbs
(7kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A(x1)
Base
NOTE: Not all hardware will be utilized
TOOLS NEEDED
B(x1)
Upper Pole
C(x1)
Middle Pole
D(x1)
Lower Pole
S-A (x4)
M5x8mm Flat
Head Screw
S-D (x2)
M5x16mm
Screw
S-B (x3)
M5x20mm
Screw
S-C (x8)
M5x8mm Round
Head Screw
W-A (x2)
ST4.8x35mm
Screw
S-E (x2)
M5 Nut
E(x1)
Adapter Plate
F(x2)
Pole Accessory Clip
G(x1)
Accessory Extension
W-B (x2)
Concrete Anchor
T-A (x1)
2.5mm Allen
Wrench
T-B (x1)
3mm Allen
Wrench

3
ASSEMBLY OPTION A: Free-Standing Option
STEP 1
STEP 2
STEP 3
Assemble Upper and Lower Poles (B,D) onto Middle Pole (C) using M5x8mm Round Head Screws (S-C)
and 3mm Allen Wrench (T-B).
Attach Base (A) to Lower Pole (D) using M5x20mm Screws (S-B) and 3mm Allen Wrench (T-B).
Attach Adapter Plate (E) to Upper Pole (B) using M5x8mm Flat Head Screws (S-A) and 3mm Allen
Wrench (T-B).
B
C
S-C
T-B
A
D
D
S-B T-B
S-A T-B
E
B

4
STEP 4
STEP 5
Attach the Dyson Docking Station that came with your Dyson vacuum to Adapter Plate (E) using
M5x16mm Screws (S-D), M5 Nuts (S-E), and a Phillips Screwdriver.
Press Accessory Clips (F) onto the assembled pole set. Route the power cable from the docking
station through the back of the stand.
Dyson Docking
Station
S-D
S-E
E
F

5
STEP 7
STEP 6
Loosen screws on Accessory Extension (G) using 2.5mm Allen Wrench (T-A) so that the red lock
adapters are able to slide freely.
Install Accessory Extension (G) onto the Dyson Docking Station and re-tighten screws using 2.5mm
Allen Wrench (T-A).
G
T-A
G
T-A

6
ASSEMBLY OPTION B: Wall Mount
WOOD STUD INSTALLATION
Hold the Dyson Docking Station that came with your Dyson vaccum against the wall with the lower
hole positioned 47 1/4” (120cm) o the ground. Mark drilling locations with a pencil. Use of a level
and stud finder is highly recommended. Make sure there is an outlet near your chosen installation
location.
Drill 1.4” (35mm) deep pilot holes using a ⅛” (3.5mm) drill bit.
Mount the Dyson Docking Station using ST4.8x35mm Screws (W-A) and a Phillips Screwdriver.
Loosen screws on Accessory Extension (G) using 2.5mm Allen Wrench (T-A) so that the red lock
adapters are able to slide freely. Install Accessory Extension (G) onto the Dyson Docking Station and
tighten screws using 2.5mm Allen Wrench (T-A).
Dyson
Docking
Station
W-A
GT-A
T-A

7
CONCRETE/BRICK INSTALLATION
Loosen screws on Accessory Extension (G) using
2.5mm Allen Wrench (T-A) so that the red lock
adapters are able to slide freely. Install Accessory
Extension (G) onto the Dyson Docking Station and
tighten screws using 2.5mm Allen Wrench (T-A).
Hold the Dyson Docking Station that came with your Dyson vacuum against the wall with the lower
hole positioned 47 1/4” (120cm) o the ground. Mark drilling locations with a marker. Use of a level is
highly recommended. Make sure there is an outlet near your chosen installation location.
Drill 1.4” (35mm) deep pilot holes using a 15/64” (6mm) drill bit.
Mount the Dyson Docking Station using
Concrete Anchors (W-B), ST4.8x35mm
Screws (W-A), and a Phillips
Screwdriver.
GT-A
W-B
W-A
T-A

LAST UPDATED: 05/10/2023
REV1
FOR MORE LIFE FINDS PRODUCTS, CHECK OUT OUR WEBSITE AT: www.lifefinds.store
[email protected]tore www.lifefinds.store 309-278-5303
Chat live with an agent!
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.