Vivo STAND-V101BB User manual

Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101bb
SKU: STAND-V101BB
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Base
B(x1)
Lower Arm
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
E(x1)
Cable Clip
F (x1)
Support Plate
G(x1)
Grommet Bolt
H (x1)
3mm Allen
Wrench
I (x1)
6mm Allen
Wrench
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5 Washer
C(x1)
Spring Arm
D(x1)
VESA Plate

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Insert 6mm Allen wrench (I) into socket on top of base (A) and turn screw counter-clockwise to lower
clamp. Place on edge of table and tighten clamp.
TOOLS NEEDED
17.6lbs
(7.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
OPTION B: Grommet Base Installation
Remove bolt (A2) and clamp (A3) from base
(A1) using 6mm Allen wrench (I). Insert
grommet bolt (G) into base. Position the base
over the desk cable grommet hole. Hold
the support plate (F) underneath the desk.
Tighten the grommet bolt into the support
plate using the 6mm Allen wrench (I).
A
I
10-50mm
G
A1
A1
A2
A3
ø 10mm
(ø 3/8" )
I
F
10-50mm

4
STEP 2
Place lower arm (B) onto base, and secure by turning the screw in back with 3mm Allen wrench (H).
STEP 3
Place spring arm (C) onto lower arm, and secure by turning the screw in the front with
3mm Allen wrench (H).
H
B
C
H

5
STEP 4
Install the VESA plate (D) to monitor using M4x12 bolts (M-A) or M5x12 bolts
(M-B) with washers (M-C), making sure the arrow in back is pointing up.
STEP 5
Pull back the release lever on the support bracket, then place the monitor with VESA
plate into the support.
TV
TV
TV
D
M- C
M- A
M- B
1
2

6
STEP 6
If needed, adjust spring arm to support the monitor using
the 6mm Allen wrench. Turn the screw in back clockwise
to increase support, and counter-clockwise to decrease.
Adjust the tilt joint to tighten or loosen tilt support.
STEP 7
Slide cable cover on lower arm forward to remove.
I
2
1
I

7
STEP 8
Install cable clip (E) to base. Organize cables, then reinstall cable cover to lower arm.
Adjust as Desired
E
+90°
-90°
±90°
±90°
H
I
±180°
±180°

LAST UPDATED: 07/03/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303