Vivo STAND-SIT2B User manual

Sit-Stand Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit2b
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-SIT2B

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
A (x1)
Keyboard
Mount
B(x1)
Clamp
C(x1)
Grommet
Base
J (x2)
Cable Clip
D(x1)
Grommet
Plate
E(x1)
Decorative Cover
F (x2)
VESA Plate
G(x1)
Arm Mount
H (x1)
Keyboard Tray
I (x1)
Pad
M-A (x8)
M4x12
M-C (x8)
M5x12
M-B (x8)
M4x16
M-D (x8)
M5x16
M-F (x8)
Spacer
M-E (x8)
D5 Washer
O (x4)
Bolt
K (x5)
Rubber Pad
L(x2)
Thumbscrew
M (x1)
Pole
N (x4)
Nut
P (x1)
3mm Allen Key
Q(x1)
6mm Allen Key
R (x1)
Wrench
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 1
Slide base cover (E) over pole (M).
TOOLS NEEDED
17.6 lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 2
OPTION A: Clamp Installation
Attach five rubber pads (K) to clamp (B). Secure pole (M) to clamp (B) by tightening grub screw in the
clamp using 3mm Allen key (P). Secure clamp to the desktop.
E
M
K
B
P
Per Arm
2.2lbs
(1kg)
Keyboard

4
STEP 2 (Continued)
OPTION B: Grommet Installation
If you are securing the stand to the desktop without clamp (B), use existing grommet hole, or drill a
⅜” (10mm) hole. Attach base (C) to pole (M). Tighten grub screws in base (C) using 3mm Allen key
(P). Attach five rubber pads (K) to the bottom of base (C). Remove screw from top of bolt in clamp
(B) using Phillips screwdriver. Remove hand bolt from clamp and use with Support Plate (D) to attach
pole (M) to desk as shown in diagram.
D
STEP 3
Slide cable management clips (J), keyboard arm (A), second cable clip (J), then monitor arms (G) over
top of pole (M) as shown in diagram. Secure both arms using 6mm Allen key (Q).
A
J
G
J
Q
P
C
K
B

5
OPTION A: Flat Back Monitor
Attach VESA plates (F) to back of monitors
using bolts (M-A,M-C) and washers (M-E).
STEP 4
OPTION B: Curved Back Monitor
Attach VESA plates (F) to back of monitors
using bolts (M-B,M-D), washers (M-E), and
spacers (M-F).
N
R
O
I
H
Attach keyboard tray (H) to arm (A) using four bolts (O) and four nuts (N). Tighten using wrench (R)
and Phillips screwdriver. Place pad (I) on le or right side of keyboard tray (H).
STEP 3 (Continued)
F
M- E
M- A
M- C
M- E
M- B
M- D
M- F
F

6
STEP 5
Slide monitors with VESA plates (F) onto monitors arms (G). Secure using thumb screws (L).
STEP 6
Adjust the tension of monitor and keyboard arms using 6mm Allen key (Q). Remove the bottom
covers as shown. Place cables into covers, then reattach to arms. Use cable management clips (J) to
further organize cables.
L
12
Q
Q
12

7
STEP 7
Adjust tension of tilt joints using 6mm Allen key (Q) to hold monitor and keyboard at desired angles.
Store Allen keys (Q, P) in clips.
Adjust as Desired
Q
P
Q
Q
+35°
-35°
90°
90°
180°
180°
90°
30°

Last Updated: 04/30/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654