Vivo STAND-V012K User manual

Pneumatic Arm Dual Monitor Extra Tall Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v012k
SKU: STAND-V012K
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x2)
Arm
B(x1)
Clamp
C(x2)
VESA Plate
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Top Pole
E(x1)
Bottom Pole
F (x1)
Pole Cap
G(x1)
Pole Connector
H (x2)
Cable Clip
S-A (x2)
M6x10
Thumbscrew
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x8)
M4x12 Screw
M-B (x8)
M4x16 Screw
M-C (x8)
M5x12 Screw
M-D (x8)
M5x16 Screw
M-E (x8)
D5 Washer
M-F (x8)
Spacer
S-B (x3)
M6x16 Screw
I(x1)
Grommet Base
J(x1)
Support Plate
M (x1)
So Pad
T-A (x1)
3mm Allen
Wrench
T-B (x1)
4mm Allen
Wrench
T-C (x1)
6mm Allen
Wrench

3
ASSEMBLY STEPS
TOOLS NEEDED
2.2-19.8lbs
(1-9kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 1
PER MONITOR
Insert Pole Cap (F) into the top of Top Pole (D).
STEP 2
Loosen the screws and disassemble the Clamp (B) and seperate into Clamp Brace (B1) and Clamp
(B2) using 4mm Allen Wrench (T-B).
T-B
F
D
B
B1
B2

4
STEP 3
OPTION A: Clamp Installation
Attach Clamp Brace (B1) to Bottom Pole (E)
using the M6x16 Screws (S-B) and the 4mm
Allen Wrench (T-B). Peel the protective film o
of So Pad (M) and place it onto Clamp Brace
(B1). For thinner desktops, re-attach the Clamp
(B2) to the Clamp Brace (B1) and tighten the
screws using the 4mm Allen Wrench (T-B).
For thicker desktops, disassemble Clamp (B2)
using a Phillips screwdriver as shown in 3.1.
Flip the L-bracket over and reassemble. Then
re-attach Clamp (B2) to Clamp Brace (B1) and
tighten the screws using the 4mm Allen Wrench
(T-B).
OPTION B: Grommet Installation
For grommet hole attachment only, cut So Pad (M)
along the indentations. Peel the protective film o
of So Pad (M) and place the pieces onto Grommet
Base (I) as shown below. If not using an existing
through-hole, using a 10mm (⅜”) drill bit, drill
through the desktop at least 2” away from the edge.
Disassemble Clamp (B2) using a Philips screwdriver.
Set aside all parts except for Clamp Bolt (B3).
Attach Bottom Pole (E) and Grommet Base (I) to the
desktop using Support Plate (J) and Clamp Bolt (B3)
as shown below.
B1
T-B
S-B
E
M
B2
B3
T-B
T-B
B3
B2
M
I
J

5
STEP 6
Attach VESA Plates (C) to the back of the monitors using Screws (M-A through M-D) and
Washers (M-E). If needed, use Spacers (M-F).
Slide Cable Clip (H) and Arm (A) onto Bottom Pole (E).
Tighten Arm (A) using 6mm Allen Wrench (T-C).
STEP 4
Attach Top Pole (D) to Bottom Pole (E) using Pole Connector (G). Once poles are fully threaded on,
tighten set screws on Pole Connector (G) using 3mm Allen Wrench (T-A). Slide Cable Clip (H) and Arm
(A) onto Top Pole (D). Tighten Arm (A) using 6mm Allen Wrench (T-C).
STEP 5
T-C
A
H
E
T-C
D
E
G
T-A A
D
T-C
H
C

6
STEP 8
Adjust gas spring support in Arms (A) using 6mm Allen wrench (T-C). Turning counter-clockwise
increases support, and clockwise decreases.
T-C
STEP 7
Slide VESA Plates (C) with monitors
over the brackets on Arms (A). Secure
using M6x10 Thumbscrews (S-A).
A
STEP 9
Remove cable management covers
from underneath Arms (A).
S-A
S-A
C
A
T-C A
A

7
STEP 9 (Continued)
Manage cables by reattching the cable management covers to Arm (A) and Cable Clips (H).
STEP 10
Adjust tilt support using 6mm Allen Wrench (T-C).
T-C
A
H

LAST UPDATED: 11/11/2021
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303