Vivo STAND-V004F User manual

Quad Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v004f
SKU: STAND-V004F
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x4)
VESA Plate
B(x2)
Arm
C(x1)
Base
M-A (x16)
M4x12
M-D (x16)
M5x16
J (x3)
Bolt
M-F (x16)
Spacer
M-E (x16)
D5 Washer
D(x1)
Pole
E(x1)
Pole
F (x1)
Pole
Connector
G(x2)
Cable Clip
H (x4)
Height
Adjustment Knob
I (x4)
Bolt
M-C (x16)
M5x12
M-B (x16)
M4x16
K (x1)
3mm Allen
Wrench
L (x1)
4mm Allen
Wrench
M (x1)
6mm Allen
Wrench
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
N (x1)
Pole Cap
TOOLS NEEDED
Phillips
Screwdriver
17.6lbs
(8kg)
PER ARM

3
ASSEMBLY STEPS
STEP 2
Attach pole (D) to base (C) using bolts (J) and 4mm allen wrench (L).
STEP 3
Slide cable management clip (G) and
arm (B) over top of pole (D) and tighten
using 6mm allen wrench (M).
D
C
J
L
D
G
B
M
Attach pole cap (N) to pole (E).
N
E
STEP 1

4
STEP 4
Attach pole (E) to pole (D) using pole connector (F). Tighten grub screws in pole connector using 3mm
allen wrench (K). Slide second cable management clip (G) and arm (B) over top of pole (E).
STEP 5
Tighten arm (B) using 6mm allen
wrench (M).
K
D
F
E
G
E
B
M

5
STEP 6
Slide VESA plates (A) onto brackets on arms (B) as shown in diagram.
STEP 7
OPTION A: Flat Back Monitor
For flat back monitor, install VESA plate (A) to monitor using bolts (M-A) or (M-C) and washers (M-E).
OPTION B: Curved Back Monitor
For curved back monitor, install VESA plate (A) to monitor using bolts (M-B) or (M-D), washers (M-E),
and spacers (M-F).
AM- A
M- C
M- E
AM- B
M- D
M- E
M- F

6
STEP 8
STEP 9
Route cables through cable management clips.
Secure monitors by placing height adjustment knobs (H) on square bolts and tightening bolts (I)
through the top.
1
I
H
M
2

7
STEP 10
Store allen wrenches (K,L,M) in cable management clips (G) for future adjustments.
STEP 11
Do not move monitors past center of gravity. This could result in tipping.
Adjust as Desired
K
L
M
+45 °
-45°
+45 °
-45°
+45 °
-45°
360 °
+45 °
-45°
360 °
360 °
360 °
M

LAST UPDATED: 07/22/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303