Vivo STAND-V102Z User manual

Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102z
SKU: STAND-V102Z
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A (x1)
Base
B(x1)
Base Cover
C(x1)
Monitor Arm
D(x1)
Pole
E(x3)
M6x14
F(x1)
4mm Allen
Wrench
G (x1)
6mm Allen
Wrench
M-A (x8)
M4x12
M-B (x8)
M5x12
M-C (x8)
D5 Washer
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

3
ASSEMBLY STEPS
TOOLS NEEDED
17.6lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 1
Press the base cover (B) onto the base (A). Assemble the pole (D) to the base using M6x14 bolts (E)
and tighten with the 4mm Allen wrench (F).
PER MONITOR

4
STEP 2
Slide the monitor arm (C) onto the pole
to the desired height, and tighten the
center bracket to the pole using the
6mm Allen wrench (G).
STEP 3
Attach two bolts (M-A or M-B) and washers (M-C) to the top mounting holes of each
monitor, making sure to leave 3mm of thread exposed.

5
STEP 4
Align bolts (M-A, M-B) in VESA plates. Secure using
two more bolts (M-A or M-B) and washers (M-C) in
the bottom two holes of each monitor. Tighten all
bolts using a Phillips screwdriver.

6
STEP 5
Tighten or loosen the tilt joints using the 6mm Allen wrench (G). Store tools in the cable clip.
STEP 6
CAUTION: To prevent tipping, please be careful not to extend the arms too far forward or backward.

7
Adjust as Desired
Adjust monitor position and rotation as desired. Manage cables using the clips on the arms and pole.

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303