Vivo STAND-V012J User manual

Dual Monitor Desk Mount with Laptop Holder
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v012j
SKU: STAND-V012J
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Bottom Pole
C(x1)
Clamp
D(x1)
Dual Arm
G (x3)
VESA Plate
S-A (x3)
M6x16mm Screw
S-B (x3)
M6 Security
Nut
M-A (x8)
M4x12mm
Thumbscrew
H (x1)
Grommet Plate
I (x1)
So Pad
J(x1)
Support Plate
K (x1)
Pole Cable Clip
L (x6)
Arm Cable Clip
M-B (x8)
M4x30mm Screw
M-C (x8)
M6 Spacer
T-A (x1)
3mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
T-C (x1)
6mm Allen
Wrench
B (x1)
Top Pole
E(x1)
Single Arm
F(x1)
Tray
M (x1)
Pole Cap
S-C (x4)
M4x8mm Screw
S-D (x4)
M4 Nut
T-D (x1)
Wrench

3
ASSEMBLY STEPS
TOOLS NEEDED
Phillips
Screwdriver
STEP 1
STEP 2 (Option A)
Loosen knob on Clamp (C).
C
Clamp Installation
Mount Clamp (C) to Bottom Pole (A) using M6x16mm Screws (S-A) 3mm Allen Wrench (T-A).
Secure assembly to desktop by tightening knob on Clamp (C).
C
A
S-A
T-A
22 lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Per Arm
11 lbs
(5kg)
Laptop Tray

4
STEP 2 (Option B)
Grommet Installation
Using a phillips screwdriver, remove the screw from Clamp (C) and disassemble. Set Knob
(C2) aside. Mount Grommet Plate (H) to Bottom Pole (A) using M6x16mm Screws (S-A)
and 3mm Allen Wrench (T-A). Remove adhesive backing from So Pad (I) and adhere to
Grommet Plate (H). Using a 3/8” (10mm) drill bit, drill through desktop surface and secure
assembly using Knob (C2) and Support Plate (J).
C
C2
H
S-A
T-A
A
I
C2
J

5
STEP 3
Slide Pole Cable Clip (K) and Single Arm (E) onto Bottom Pole (A). Secure Single Arm (E) in
place using 6mm Allen Wrench (T-C). Thread Top Pole (B) onto Bottom Pole (A). Slide Dual
Arm (D) onto Top Pole (B). Secure Dual Arm (E) in place using 6mm Allen Wrench (T-C).
Attach Pole Cap (H) to Top Pole (B).
K
E
A
T-C
B
E
H
T-C

6
STEP 4
STEP 5
Attach Arm Cable Clips (L) to Dual Arm (D) and single Arm (E).
Assemble Laptop Tray (F) to VESA Plate (G) using M4x8mm Screws (S-A) an M4 Nuts (S-B). Tighten the
assembly using Wrench (T-D) and a Phillips screwdriver.
L
D
E
F
G
S-A
S-B
T-D

7
STEP 6
Slide Tray (F) with VESA Plate (G) onto Single Arm (E). Secure VESA Plate (G) in place using
M6 Security Nut (S-B).
FG
E
S-B

8
STEP 7
Secure VESA Plates (G) to monitors using M4x12mm Thumbscrews (M-A) or M4x30mm
Screws (M-B). M6 Spacers (M-C) may be required.
G
G

9
STEP 8
Slide monitors with VESA Plates (G) onto Dual Arm (D). Secure VESA Plates (G) in place
using M6 Security Nuts (S-B).
S-B
GD

10
STEP 9
Manage cable using Pole Cable clip (K) and Arm Cable Clip (L).
L
K