Vivo STAND-V004T User manual

Quad Monitor Stand
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-Model: STAND V004T
Tools Required:
phillips screwdriver
Package Contents
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
A (x1)
Pole
B (x1)
Weighted Base
C1 (x1)
Monitor Arm
C (x2)
Monitor Arm
D (x1)
Plastic Cover
F (x1)
Support Plate
G (x1)
M10 Washer
H (x1)
Spring Washer
I (x4)
M x10
J (x3)
M6x29
K (x1)
Allen Key
L (x1)
Wrench
M (x16)
M4x12
O (x16)
M4 Spacer
P (x2)
Spare Cover
E (x1)
M10 Bolt
N (x16)
M4x30
- -https://vivo us.com/products/stand v004t

0
Assembly Steps
2
Step 1: Mounting the Base Accordingly
Option A: Weighted Base
Option B: Grommet Base
Attach pole (A) to weighted base (B)
using screws (J). Slide decorative cover
(D) onto pole (A).
Slide spring washer (H) onto
grommet bolt (E). Slide
washer (G) onto grommet
bolt (E). Slide support plate
(F) onto grommet bolt (E).
Insert grommet bolt (E)
through desk from bottom.
Thread pole (A) onto
grommet bolt (E). Tighten
with wrench (L). Slide
decorative cover (D) onto
pole (A).
Step 1: Mounting the Base Accordingly (Continued)
Option C: Grommet Installation
with Weighted Base
Step : Install Monitor Arm to the Pole
Attach pole (A) to weighted
base (B) using screws (J). Slide
spring washer (H) onto
grommet bolt (E). Slide washer
(G) onto grommet bolt (E). Slide
support plate (F) onto grommet
bolt (E). Insert grommet bolt (E)
through desk and weighted
base (B) from bottom. Tighten
with wrench (L). Slide
decorative cover (D) onto pole
(A).
Attach monitor arm (C1) to pole (A) with screws (I) as shown in
diagram. Attach monitor arm (C2) to pole (A) with screws (I) as shown
in diagram.
a

Step 4: Do the Necessary Judgment
Use allen wrench
(K) to adjust
tension. Use
wrench (L) to
tighten nut if the
tilt angle cannot be
fixed.
Turn the bolt counterclockwise using allen wrench (K) to lower the
center monitor. Turn the bolt clockwise using allen wrench (K) to raise
the center monitor.
Step 3: Mount the Monitor to VESA Plate
Option A: Flat Back Monitor
Option B: Curved Back Monitor
Mount monitors to
VESA plates. For flat
back monitors use
thumbscrews (M).
For curved back
monitors use screws
(N) and spacers (O) as
shown in diagram.
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
Safety Warning
Contact us at:
Last updated: 0 /30/18
Step 5: Manage the Wires
Manage wires and adjust monitors as desired.
4