Vivo STAND-V001D User manual

Single Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001d
SKU: STAND-V001D
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Column
B(x1)
VESA Plate
C(x1)
Base
J (x3)
M6x10
L (x1)
5mm Allen
Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x4)
M4x8
E(x4)
M4x12
F (x4)
M4x30
G(x4)
Spacer
H (x1)
Knob
I (x1)
Washer
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M (x4)
Rubber Pad
K (x1)
4mm Allen
Wrench
N (x1)
Washer

3
ASSEMBLY STEPS
STEP 1
STEP 2
Apply pads (M) to underside of base (C).
Mount column (A) to base (C) using M6x10 bolts (J) and tighten with Allen wrench (K).
J
M

4
STEP 3
Attach VESA plate (B) to column (A) using knob (H), washer (I), and washer (N).
I
N
14x6.5x1.5
16x6.2x1.5

5
STEP 4
OPTION A: Flat Back Monitor
Insert M4x8 or M4x12 screws (D, E) into top two holes of monitor, leaving 3mm of thread exposed.
Hang monitor over slots in VESA mount, insert M4x8 or M4x12 screws into bottom two holes, then
tighten.
D,E
D,E

6
STEP 4 (continued)
OPTION B: Curved Back Monitor
Insert M4x30 screws (F) with spacers (G) into top two holes of monitor, leaving 3mm of thread exposed.
Hang monitor over slots in VESA mount, insert M4x30 screws with spacers into bottom two holes, then
tighten.
F
13x5.5x16.5
13x5.5x16.5 F

7
STEP 5
Adjust monitor height by loosening the knob (H), then tighten at desired height (NOTE: hold monitor
when adjusting height). Adjust tilt joint using the 5mm Allen key (L).

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303