Vivo MOUNT-E-MM070 User manual

Electric TV Wall Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-e-mm070
SKU: MOUNT-E-MM070
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
77lbs
(35kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
A (x1)
Mount
B(x2)
Wall Plate Cover
C(x1)
Stencil
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
TV Plate
E (x2)
VESA Bracket
F (x1)
Front Cover
G (x1)
Remote
H(x1)
Power Cord
I(x1)
Wrench
M-A (x4)
M5x14
M-B (x4)
M6x14
M-C (x4)
M6x30
M-D (x4)
M8x30
M-E (x4)
M8x50
M-F (x4)
Square
Washer
M-G (x8)
5mm Spacer
M-H (x8)
15mm Spacer
W-A (x6)
Screw
W-B (x6)
Anchor
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 309-278-5303.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
W-C (x6)
Washer

3
ASSEMBLY STEPS
STEP 1
Measure the required mounting height using the
chart below. Ensure the front edge of the mantel
does not exceed 110°F (43°C).
STEP 2
Remove pre-installed nuts (A1), metal washers
(A2) and plastic washers (A3) from the mount (A)
using the wrench (I).
STEP 3
OPTION A: Wood Wall Installation
Align the bottom edge of the stencil (C)
with the measured height from step
1 and mark drilling locations using a
pencil. Use of a stud finder and level
is recommended. Remove stencil and
drill 2.2” (55mm) deep holes using a
1/4” (6mm) drill bit. Attach the mount
(A) to the wall using screws (W-A) and
washers (W-C).
TOOLS NEEDED
3/8” Drill Pencil
Phillips
Drill
3/16” Drill
Hammer Ruler Stud Finder
≤ 13-3/4” (350mm)
≤ 4” (100mm)
≤ 7-7/8” (200mm)
≤ 11-3/4” (300mm)
≥ 9-7/8” (250mm)
≥ 7-7/8” (200mm)
≥ 3-1/8” (80mm)
≥ 11-3/4” (300mm)

4
STEP 4
Plug the power cord (H) into mount (A). Place the cord into the slot as shown and snap the wall plate
covers (B) in place.
STEP 3 (Continued)
OPTION B: Concrete/Brick Installation
Align the bottom edge of the stencil (C)
with the measured height from step 1
and mark drilling locations using a pencil.
Use of a level is recommended. Remove
stencil, drill 2.4” (60mm) deep holes using
a 3/8” (10mm) drill bit, and insert anchors
(W-B) into the holes. Attach the mount
(A) to the wall using screws (W-A) and
washers (W-C).

5
STEP 5
Plug the power cord (H) into a wall outlet. Press and hold the down button on the remote (G) until the
arm is fully lowered. Remove and discard the silicon shipping pad (A4). Please note that the arm is
not able to fully raise until the pad is removed.
STEP 6
Remove the nut from each VESA bracket (E) and flip open the clip.

6
STEP 7
Attach the VESA brackets (E) to the back of the TV
using combination of screws (M-A - M-E), washers
(M-F) and spacers (M-G, M-H) appropriate for your
TV. The bottom edge of the VESA brackets should be
greater than 7-7/8” (200mm) above the bottom edge
of the TV.
STEP 9
Hang the TV with VESA brackets (E) onto the TV plate (D). Close the clips, and secure using
the previously removed nuts. Tighten with the wrench (I).
STEP 8
Place previously removed plastic washers (A3) on the mount (A). Attach the TV plate (D) to the mount
using nuts (A1) with metal washers (A2). Make sure the TV plate is level, and tighten nuts using the
wrench (I). Press the front cover (F) onto the front of the TV plate.

7
STEP 10
Manage cables using the cable clips on the arm. Use the remote (G) to raise and lower the mount.
The TV may be manually swiveled to the le and right.
CAUTION: To avoid injury, do not place hand in the arm while operating.

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303