Vivo MOUNT-CAR01 User manual

Car Laptop Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-car01
SKU: MOUNT-CAR01
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
ASSEMBLY STEPS
TOOLS NEEDED
11lbs
(5kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
STEP 1
Begin by identifying what foot style is needed for your passenger seat configuration, using
the images below. Please note that the two front seat bolts of some vehicles will dier from
each other in angle.
Attach the appropriate foot for the passenger seat’s le bolt [ 0° Foot (B), 90° Foot (C),
or 45° Foot (D) ] to the left underside of of Base (A) using M6x10mm Screws (S-A) M6
Washers (S-B), and a Phillips screwdriver.
A(x1)
Base
B(x2)
0° Foot
C(x2)
90° Foot
D(x2)
45° Foot
F(x1)
Pole
G(x1)
Arm
L(x1)
Connecting
Bracket
Q(x1)
Velcro
Strap
S-A (x4)
M6x10mm
Screw
S-B (x8)
M6 Washer
S-C (x2)
M6 Nut
S-D (x4)
M5x10mm
Screw
S-E (x4)
M5 Nut
S-F (x8)
M5x6mm
Screw
S-G (x2)
M4x5mm
Thumbscrew
S-H (x2)
M4 Washer
S-I (x1)
M6 Flanged Nut
S-J (x1)
M6x45mm
Screw
T-A (x1)
5mm Allen
Wrench
T-B (x1)
Wrench
M(x2)
Strap
Brackets
N(x2)
Lower Laptop
Arm
O(x2)
Upper Laptop
Arm
P(x2)
Screw Cap
H(x1)
Laptop Tray
I(x4)
Knob
J(x2)
Cable Clips
K(x2)
Support Screw
PACKAGE CONTENTS
Install compatible Foot (B, C, D) for your passenger seat’s le bolt to the threads on
Connecting Bracket (L) using M6 Nuts (S-C), M6 Washers (S-B), and Wrench (T-B). Please
note, based on your passenger seat’s floor bolts, you may need a dierent foot than what was
used above.
L
A
B
C
T-B
S-B
S-C
C
D
D
0°
0°
0°
90°
90°
90°
45°
45°
45°
B
S-A
S-B
Socket
Wrench
OR OR

4 5
STEP 2
Loosely assemble the right foot assembly to Base (A) using M6x10mm Screws (S-A),
M6 Washers (S-B), and a Phillips screwdriver. Align the le foot with the le seat bolt on the
passenger seat. Adjust the right foot to match up with the right bolt on the seat and tighten
M6x10mm Screws (S-A).
Attach Pole (F) to back of Base (A) using Knobs (I).
Thread Support Screws (K) onto Base (A) and place Screw Caps (P) onto the ends once
threaded.
Loosen the front seat bolts on passenger seat using a socket wrench (size needed depends
on manufacturer).
Slide the le foot under the le seat bolt and the right foot under the right seat bolt.
Adjust the placement as needed and re-tighten bolts.
A
S-B
S-A
STEP 3
STEP 4
STEP 5
F
K
P
A
I
A

6 7
STEP 6
STEP 7
G
F
T-A
1. Slide Arm (G) onto Pole (F) with the
adjustment bolt pointing up. Tighten and
secure with 5mm Allen Wrench (T-A). Adjust
the swivel using 5mm Allen Wrench.
2. Determine desired Pole (F) height and
Insert M6x45mm Screw (S-J) into slot.
Secure using M6 Flanged Nut (S-I), making
sure the flanged, wider part of the nut is
faing outward, with the hex side fitting into
the hex indention on Pole (F).
Secure Strap Brackets (M) to Laptop Tray (H) using M5x6mm Screws (S-F) and a Phillips
Screwdriver.
T-A
Attach Lower Laptop Arms (N) with tab pointing up to underside of Laptop Tray (H) using
M5x6mm Screws (S-F) and a Phillips screwdriver. Connect Upper Laptop Arms (O) to front
tab of Lower Arms (N) using M4 Washers (S-H) and M4x5mm Thumbscrews (S-G).
Note: Lower Laptop Arms (N) can be pointed down to allow for thinner laptops (0 to 0.5”) to be
used with mount.
Note: Lower Laptop Arms (N) installed in the up position is compatibile with laptops 0.5” to
1.25” in thickness.
STEP 8
Connect Laptop Tray (H) to assembly using M5x10mm Screws (S-D), M5 Nuts (S-E), and
a Phillips screwdriver. Use 5mm Allen Wrench (T-A) to adjust the tilt and swivel on VESA
bracket. Place Cable Clips (J) on Arm (G) to manage cables. Tighten Support Screws (K) to
level the mount.
Feed Velcro Strap (Q) through Strap
Brackets (M). Use to secure laptop to tray.
STEP 9
S-F
H
M
S-F
H
N
S-G
O
S-H
T-A
T-A
S-I
S-J
J
Q
M

LAST UPDATED: 03/01/2023
REV1.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303