Vivo STAND-V002E User manual

Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002e
SKU: STAND-V002E
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Pole
B(x1)
Clamp
C(x1)
Grommet Base
J (x2)
Cable Clip 2
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Arm Support
Bracket
E(x2)
VESA Bracket
F (x2)
Arm
G (x1)
Pole Cap
H (x1)
Cable Clip
I (x1)
Plastic Cover
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x2)
Arm Cap
O (x1)
3mm Allen
Wrench
L (x1)
Support Plate
M (x5)
Rubber Pad
N (x2)
M5x7
P (x1)
4mm Allen
Wrench
Q (x1)
6mm Allen
Wrench
M-A (x8)
M4x12
M-B (x8)
M5x12
M-C (x8)
D5 Washer

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
OPTION A: Clamp Installation
Slide cable management clip (H) and plastic cover (I) onto bottom of pole (A). Stick rubber pads (M)
to bottom of clamp (B). Thread pole (A) onto clamp (B). Tighten grub screws in bottom of clamp (B)
using 3mm allen wrench (O). Secure clamp (B) to desktop as shown in diagram.
STEP 2
Insert pole cap (G) into pole (A).
10-88mm
O
M
H
I
B
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
A G

4
STEP 2 (Continued)
OPTION B: Grommet Base Installation
Remove screw from top of bolt in clamp (B). Stick rubber pads (M) to bottom of grommet base (C).
Slide cable management clip (H) and plastic cover (I) onto bottom of pole (A). Thread pole (A) onto
grommet base (C). Tighten grub screws in bottom of grommet base (C) using 3mm allen wrench (O).
Slide support plate (L) over bolt and slide through grommet hole in bottom of desktop. Thread into
bottom of pole (A).
STEP 3
Adjust height of stopper using 3mm allen wrench (O).
B
10-80mm
H
I
L
O
C
M
O
O

5
STEP 4
Remove screws from support bracket (D) using 4mm allen wrench (P). Insert arms (F) into support
bracket (D) as shown in diagram and re-insert screws using 4mm allen wrench (P).
STEP 5
Slide VESA mounts (E) onto arms (F) and tighten using 4mm allen wrench (P). Slide on arm caps (K)
and secure with screws (N).
STEP 6
Attach wire clips (J) to arms (F) as shown in diagram. Slide arms (F) onto pole (A) as shown in diagram
and tighten with 4mm allen wrench (P).
D
P
F
P
N
P
KE
P
J

6
STEP 7
Insert screws (M-A or M-B) and washers (M-C) into top two holes on monitors. Leave slightly loosened.
Slide monitors onto VESA plates and insert screws (M-A or M-B) and washers (M-C) into bottom two
holes on monitors. Tighten all screws.
STEP 8
Adjust the tilt angle of monitors using 6mm allen wrench (Q) as shown in diagram.
M- A
M- B
M- C
3m m
M- A
M- B
M- C
1 2
3
+45 °
-45°
Q

7
STEP 9
Adjust as Desired
Store allen wrenches (O, P, Q) as shown in diagram.
P
Q
360°
30°
360°
30°

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303