Vivo STAND-V012TW User manual

White Dual Vertical Monitor Extra Tall Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v012t
SKU: STAND-V012TW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Pole Set
B(x1)
Clamp
C(x1)
Clamp Brace
I(x1)
M10 Washer
L1 (x3)
Wire Clip
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M(x1)
Allen
Wrench Set
L2 (x4)
Wire Clip
D(x2)
Swivel Arm
E(x2)
VESA Plate
F (x3)
M5x14
G(x2)
M8x12
H (x2)
Nut
K (x1)
Grommet
Base Plate
J(x1)
Spring Washer
O(x8)
M4x30
P (x8)
M4 Spacer
N (x8)
M4x12
Thumbscrew
Q1 (x1)
So Pad
Q2 (x1)
So Pad

3
TOOLS NEEDED
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
ASSEMBLY STEPS
STEP 1
ASSEMBLE POLE SET
Thread the Pole Set (A) together as shown below.
PER ARM
Option A: Desk Clamp Install
1. Install the clamp brace (C) to the pole (A) using x3 M5x14 bolts (F). See Figure 1.
2. Attach so pad (Q1) to the clamp brace (C) , see Figure 2.
3. Install the clamp (B) to the pole assembly according to the thickness of the desktop. The
thickness can be changed to 3 positions. Connect using x2 M8x12 bolts (G) and tighten using the
Allen key (M). Tighten the clamp to the desktop using the plastic knob. See Figure 3.
a
Figure 1 Figure 2
Q1
F
C
A
M
G
B
Drill

4
STEP 1 (Continued)
Install the swivel arms (D) to the pole (A). Fasten the bolts with the 6mm Allen wrench (M). Attach the
wire clips (L1, L2) to the pole (A) and swivel arms (D).
STEP 2
Option B: Grommet Install
1. If desk does not have an existing grommet
hole, drill a 3/8” (10mm) diameter hole at the
desired position through the mounting surface.
2. Completely disassemble clamp (B) into
individual parts. Set knob (B1) and clamp
plate (B2) aside for later use. The L bracket,
bolt, washer and bushing will not be used.
3. Install grommet base plate (K) to the pole (A)
using x3 M5x14 bolts (F). See Figure 4.
4. Attach so pad (Q2) to the grommet base plate
(K), see Figure 5.
5. Position pole (A) on the mounting surface
and secure using the clamp plate (B2), spring
washer (J), M10 washer (I) and knob (B1). See
Figure 6.
B1
B2
B2
B1
a
m
f
Figure 4
t2 Figure 5
a
m
f
Figure 4
t2 Figure 5
A
K
J
I
Q2
F

5
STEP 3
OPTION A: Flat Back Monitor
Attach the VESA plates (E) to the monitors with
M4x12 thumb bolts (N).
NOTE: Hand tighten screws to avoid stripping
plastic screw heads.
Slide the monitors onto the heads of
swivel arms (D).
OPTION B: Curved Back Monitor
Attach the VESA plates (E) to the monitors with
M4x30 bolts (O) and M4 spacers (P).
NOTE: Gently tighten with a screwdriver.
STEP 4
Install the security nuts (H). Make sure the security
nuts are installed before you rotate the monitors.
h
N
O
P
H
E
E

6
STEP 5
Tighten the bolt on the side of the tilt joint with the 5mm Allen wrench (M) to fix the tilt angle.
Adjust the swivel joints by tightening or loosening the top bolts using the 5mm Allen wrench (M).
M
M

7
STEP 6
Manage cables and store Allen wrenches (M) in wire clip (L1) for future use.
L2
L1

LAST UPDATED: 06/07/2022
REV1
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303