Vivo STAND V001B User manual

Monito Des Mount
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-Model STAND V001B
Tools Requied
phillips screwdriver
Pacage Contents
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
- -https vivo us.com poducts stand v001b
A (x1)
Bas Stand
B (x2)
Botto Support
C (x1)
Clap
D (x2)
Support Covr
E (x1)
Lon Scrw
F (x1)
Botto Support
G (x1)
Clap Knob
H (x5)
Bolts
I (x1)
Support Plat
J (x1)
4 Alln K
K (x1)
5 Alln K
-M C (x4)
D5
-M A (x4)
M4x12
- M B (x4)
M5x12

Step 2 Install the Monito to the VESA Mount
Install two screws (M-A or M-B) with washers (M-C) in top 2 holes of monitor, leaving
3mm of thread exposed. Hang monitor over the top two slots in the VESA plate,
install two bottom screws with washers, then tighten top screws.
Assembl- Steps
2
Step 1 Install the Pole to the Destop
Option A Des Clamp Installation
Option B Gommet Base Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a
flat surface before installing the desk mount. Slide long screw (E) through the top of
Bottom Support (F) and install on base of monitor stand with Bolts (H) using 4mm
Allen Wrench (J). Position stand on desk with Long Screw through hole and secure by
using the Support Plate (I), and Clamp Knob (G) on the underside of the mounting
surface. NOTE: For self-drilled grommet installation drill a 8. mm hole or larger
through the mounting surface. Install following the above instructions.
Install Bottom
Support (B) onto
base of monitor
stand with Bolts (H)
using provided 4mm
Allen Wrench (J).
Select mounting
holes on bottom
support depending
on the thickness of
your desk and secure
clamp (C) with Bolts
(H) using 4mm Allen
Wrench (J). Place
cover (D) onto back
of the bottom
support (B).

Replace covers making sure the cables have enough slack to allow free movement of
the arm. If using clamp option, use cover (D) for additional cable management.
Step 3 Cable Management (Continued)
3b
Step 3 Cable Management
Remove cable covers from upper and lower arms. To remove lower cover, remove
the screw as shown, pull slightly forward, up and off.
3a
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
Safet- Waning
Contact us at
Last updated: 0 /21/18
Adjust as Desied
Adjust arm tension by turning screw on top of center joint with mm Allen Wrench
(K). Clockwise reduces tension, counter-clockwise increases tension. The tension
should be just enough to hold your monitor in place without lifting itself up. If
needed, adjust the bolts on the sides of the hinge behind VESA plate to tighten or
loosen the tilt angle.
4