Vivo STAND-V102AF User manual

Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102af
SKU: STAND-V102AF
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
d(x1)
Decorative
Cover
c(x1)
Monitor Arm
a(x1)
Pole
e(x3)
M6x29
i(x8)
M4x30
f(x2)
M8x10
b(x1)
Weighted Base
g(x4)
Wire Clip
l(x2)
Spare Cap
k(x2)
Security Nut
j(x8)
M4 Spacer
h (x8)
M4x12
o(x2)
VESA Plate
n (x1)
Wrench
m (x1)
Allen Wrench
Set
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

3
ASSEMBLY STEPS
STEP 1
Install the pole (a) to the weighted base (b)
using M6x29 bolts (e). Tighten with a Phillips
screwdriver and install decorative cover (d).
TOOLS NEEDED
22lbs
Per Monitor
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver Drill
a
b
d
e

4
STEP 2
Carefully slide monitor arm (c) down onto the pole, making sure holes for wire clips are facing down,
and secure with M8x10 bolts (f) using the medium Allen wrench (m). Attach the wire clips (g) to the
monitor arm.
STEP 3
OPTION A: Flat Back Monitor
Attach the VESA plates (o) to the monitors using M4x12 thumb bolts (h).
NOTE: Hand tighten screws to avoid stripping the plastic screw heads.
h
o
g
a
fm

5
STEP 3 (Continued)
OPTION B: Curved Back TV
Attach the VESA plates (o) to the monitors using M4 spacers (j) and M4x30 bolts (i). Tighten with a
Phillips screwdriver.
STEP 4
Slide the monitors onto the heads of monitor arm and install the security nuts (k). Make sure the
security nuts are installed before you rotate the monitors.
j
i
o
k

6
STEP 5
STEP 6
Pry o the plastic cover and tighten the nut on the side of the tilt joint with the wrench (n) to fix
the tilt angle. To level the monitors, remove the security nut and turn the bolt with the small Allen
wrench (m) to raise or lower the monitor. Replace nut aer the adjustment.
Pry o the plastic cover and use the large Allen wrench (m) to adjust swivel joints if needed.
Fix the tilt angle
n
m
m

7
STEP 7
Manage cables using the wire clips (g). Remove the split cap from the pole and feed cables
through, pulling ends out from the opening in back. Replace the split cap when finished.

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303