Vivo MOUNT-PC06L User manual

Large Under Desk PC Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-pc06l
SKU: MOUNT-PC06L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
A (x1)
Mount
B (x1)
Brace
C (x6)
Pad
W-A (x4)
ST4.8x16mm
Screw
W-B (x4)
ST4.8x38mm
Screw
W-C (x4)
Concrete
Anchor
T-A (x1)
3mm Allen
Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
Drill
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
ASSEMBLY STEPS
STEP 1
Remove protective lm from Pads (C) and apply to Brace (B).
44 lbs
(20 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Pencil
Phillips
Screwdriver
CB

3
STEP 2
STEP 3
Remove the Support Bar (B1) from Brace (B) using the 3mm Allen Wrench (T-A). Install the Support
Bar (B1) and Brace (B) onto Mount (A) using the previously removed hardware and 3mm Allen
Wrench (T-A).
Adjust assembled mount as needed to t your PC. This will help gauge the space consumed by the
mount when determining your desired mounting location.
DEPTH:
Loosen Set Screw (B2)
on Support Arm (B) and
slide to adjust to desired
PC depth, then retighten.
WIDTH:
Use a Phillips screwdriver to
loosen Set Screw (A1) on lower
Mount (A), then pull to adjust to
desired width and then retighten.
HEIGHT:
Pull and hold Side Pin (A2)
on Mount (A) and adjust to
desired height. Release pin
when necessary height is
reached.
1
1
2
2
3
3
B1
T-A
T-A
B
B
B1
A
B2
B
A1
AA
A2
CPU Maximum Height:
656mm/25.82”

4
INSTALLATION STEPS
Desk Mount
INSTALLATION OPTIONS:
Choose your desired installation method and follow appropriate steps below.
Desk Mount
Page 4
Wood Wall Mount
Page 5
Brick/Cement Wall Mount
Page 6
STEP 1
STEP 2
Hold Mount (A) up to desired mounting location and mark hole locations using a pencil. When
marking the keyhole locations, ensure to only mark the narrow section of the keyhole.
Drill 0.4” (10mm) deep holes using a 0.125” (3.5mm) drill bit. Using a Phillips screwdriver, partially
install two ST4.8x16mm Screws (W-A) in-line with the keyhole locations on Mount (A) leaving at least
a 4mm gap.
A
W-A

5
Wood Wall Mount
STEP 1
STEP 2
STEP 3
Hold Mount (A) up to desired mounting location and mark hole locations using a pencil. When
marking the keyhole locations, ensure to only mark the narrow section of the keyhole. Drill 1.5”
(38mm) deep holes using a 0.125” (3.5mm) drill bit.
Using a Phillips screwdriver, partially install two ST4.8x38mm Screws (W-B) in-line with the keyhole
locations on Mount (A) leaving at least a 4mm gap.
Hang Mount (A) over screws, making sure they are in the larger part of the keyhole openings. Slide the
mount toward the narrow keyhole opening to lock into place. The screw heads should now be holding
up the unit. Tighten the screws fully and install the remaining two ST4.8x16mm Screws (W-A) using a
Phillips screwdriver.
Proceed to Placing PC in
Mount step on page 7.
A
W-A
A
W-B

6
STEP 3
Hang Mount (A) over screws, making sure they are in the larger part of the keyhole openings. Slide
the mount toward the narrow keyhole opening to lock into place. The screw heads should now be
holding up the unit. Tighten the screws and install the remaining two ST4.8x38mm Screws (W-B) using
a Phillips screwdriver.
Concrete/Brick Wall Mount
STEP 1
STEP 2
Hold Mount (A) up to desired mounting location and mark hole locations using a pencil. When
marking the keyhole locations, ensure to only mark the narrow section of the keyhole. Drill 1.5”
(38mm) deep holes using a 0.25” (6mm) drill bit. Insert Concrete Anchors (W-C) into the drilled holes.
Using a Phillips screwdriver, partially install two ST4.8x38mm Screws (W-B) in-line with the keyhole
locations on Mount (A) leaving at least a 4mm gap.
Proceed to Placing PC in
Mount step on page 7.
W-B
A
W-C
W-B

7
Placing PC in Mount
ALL INSTALLATION TYPES:
STEP 3
Place your PC on Mount (A) and adjust the back brace and side support locations as needed.
Use 3mm Allen Wrench (T-A) to loosen the the Support Bar (B1) on Brace (B) and adjust the height to
clear any cables protruding from the PC.
Hang Mount (A) over screws, making sure they are in the larger part of the keyhole openings. Slide the
mount toward the narrow keyhole opening to lock into place. The screw heads should now be holding
up the unit. Tighten the screws and install the remaining two ST4.8x38mm Screws (W-B) using a
Phillips screwdriver.
W-B
DEPTH:
Loosen Set Screw (B2)
on Support Arm (B) and
slide to adjust to desired
PC depth, then retighten.
WIDTH:
Use a Phillips screwdriver to
loosen Set Screw (A1) on lower
Mount (A), then pull to adjust to
desired width and then retighten.
HEIGHT:
Pull and hold Side Pin (A2)
on Mount (A) and adjust to
desired height. Release pin
when necessary height is
reached.
B2
B
A1
AA
A2
1
1
2
2
3
3

LAST UPDATED: 05/11/2023
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303