Vivo STAND-V103F User manual

Triple Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v103f
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V103F

2
PACKAGE CONTENTS
WARNING!
A (x1)
Pole
B(x1)
Weighted Base
C(x1)
Decorative
Cover
P1 (x2)
VESA Plate
(side)
M(x2)
Spare Plastic
Cover
O(x1)
Wrench
I (x2)
M8x10 Bolt
K (x12)
M4x30 Bolt
L (x12)
M4 Spacer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
J(x12)
M4x12
Thumbscrew
D1 (x1)
Monitor Arm
(center)
D2 (x2)
Monitor Arm
E (x4)
Monitor Arm
Cover
F(x4)
Plastic Pad
G (x2)
M10x47 Bolt
H (x3)
M6x29 Bolt
N(x1)
Allen Wrench
Set
P2 (x1)
VESA Plate
(center)
Q1 (x2)
Security Nut
Q2 (x1)
M4x6 Bolt
R(x4)
Wire Clip
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
Install the pole (A) to the weighted base (B) using M6x29 bolts (H).
Tighten with a Phillips screwdriver and install decorative cover (C).
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
a
c
h
b

4
Assemble the monitor arms (D1, D2) by placing plastic pads (F) on the top and bottom of arms (D2)
and inserting them into the center arm (D1) as shown in the diagram. Secure with M10x47 Bolts (G)
and tighten with the large Allen wrench (N). Press monitor arm covers (E) onto the top and bottom of
arm joints.
STEP 3
Carefully slide assembled monitor arm down onto the
pole, making sure holes for wire clips are facing down, and
secure with M8x10 bolts (I) using the medium Allen wrench
(N). Attach the wire clips (R) to the monitor arm.
STEP 2
2.1
d2
d2
d1
e
e
g
n
f
2.2
2.3
i
r

5
STEP 4
OPTION A: Flat Back Monitor
Attach the VESA plates (P1, P2) to the monitors
using M4x12 thumb bolts (J).
NOTE: Hand tighten screws to avoid stripping the
plastic screw heads.
OPTION B: Curved Back Monitor
Attach the VESA plates (P1, P2) to the monitors
using M4 spacers (L) and M4x30 bolts (K). Tighten
with a Phillips screwdriver.
STEP 5A
Slide the center monitor onto the head of monitor arm. Secure with the M4x6 bolt (Q2) and tighten
with a Phillips screwdriver.
j
p1
j
p2
l
k
p2
l
k
p1
q2
d1,d2

6
STEP 6
Pry o the plastic cover and tighten the nut on the side of the tilt joint with the wrench (O) to fix the
tilt angle of side monitors. Tighten the grub screw on the back of center monitor joint using the small
Allen wrench (N) to fix tilt angle of center monitor.
STEP 5B
Slide the side monitors onto the heads of monitor arm and install the security nuts (Q1). Make sure
the security nuts are installed before you rotate the monitors.
n
grub
screw
Fix the tilt angle
o
q1
d1,d2

7
STEP 7
STEP 8
Pry o the plastic cover and use the large Allen wrench (N) to adjust swivel joints if needed.
To adjust center monitor height, turn the screw behind center monitor joint using the medium Allen
wrench (N). To level the side monitors, remove the security nut and turn the bolt with the small Allen
wrench (N) to raise or lower the monitor. Replace nut aer the adjustment.
n
n
STEP 9
Manage cables using the wire clips (R). Remove the split cap from the pole and feed cables through,
pulling ends out from the opening in back. Replace the split cap when finished.

Last Updated: 09/09/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654