Vivo STAND-V006 User manual

Hex Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v006
SKU: STAND-V006
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Pole
B1 (x1)
Clamp
B2 (x1)
Clamp
Brace
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
C(x1)
Decorative
Cover
D (x2)
Monitor Arm
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
E (x1)
Support Plate
S-F (x1)
M10 Washer
F(x1)
Foam Pad
S-G (x24)
M4x12 Thumb Screw
S-I (x24)
M4 Spacer
S-J (x2)
Spare Cap
T-A (x1)
Allen Wrench
Set
T-B (x1)
Wrench
G (x4)
VESA Plate
H (x2)
VESA Plate
I (x4)
Nut
S-K (x2)
M4x6
J(x8)
Wire Clip
S-A (x3)
Clamp Brace Bolt
S-B (x2)
M10x15
S-C (x4)
M8x10
S-D (x1)
M10 Bolt
S-E (x1)
Spring Washer
S-H (x24)
M4x30

3
ASSEMBLY STEPS
TOOLS NEEDED
Phillips
Screwdriver
STEP 1
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
Figure 2
OPTION A: Clamp Base Installation
Attach Clamp Brace (B2) to Pole (A) with Clamp Brace Bolts (S-A). Attach Clamp (B1) to clamp brace
at desired height using M10x15 Bolts (S-B) with Allen Wrench (T-A). Tighten Clamp to desk and slide
Decorative Cover (C) into place.
OPTION B: Grommet Base Installation
If drilling is required, drill a 3/8” (10mm) diamater hole at desired location. If there is an existing hole,
the hole must not be larger than 3” (76mm) in diameter. Apply Foam Pad (F) to base of Pole (A). Mount
Pole (A) to grommet hole in desk using M10 Bolt (S-D), Spring Washer (S-E), M10 Washer (S-F) and
Support Plate (E). Tighten with Wrench (T-B) and slide Decorative Cover (C) into place.
A
S-A
B2
C
S-B
Eye Bolt
T-A
A
F
A
C
E
S-E
S-F
S-D
B1

4
STEP 2
STEP 3
r
Install Wire Clips (J) on Arms (D). Install Arms (D) on Pole (A) at desired height using M8x10 Bolts (S-C)
with Allen Wrench (T-A), making sure Wire Clips (J) are facing down.
3A: Side VESA Plates
For monitors with flat back attach VESA Plates (G) with Thumb Screws (S-G). For monitors with
curved back attach VESA plates (G) with Screws (S-H) and Spacers (S-I). Screws only need to be
finger-tight.
3B: Center VESA Plates
For monitors with flat back attach VESA Plates (H) with Thumb Screws (S-G). For monitors with
curved back attach VESA plates (H) with Screws (S-H) and Spacers (S-I). Screws only need to be
finger-tight.
T-A
S-C
J
D
A
G
G
S-G S-I
S-H
S-G
H
H
S-H
S-I

5
STEP 4
4B: Center VESA Plates
Slide monitor onto the head of Arms (D) as shown in the diagram. Secure with M4x6 Screw (S-K).
Slide top monitors onto mount in same fashion.
4A: Side VESA Plates
Slide monitor onto the head of Arms (D) as shown in the diagram. Secure with Nut (I).
D
I
D
S-K

6
STEP 5
STEP 6
Fix the tilt angle
u
Remove plastic cover and use Wrench (T-B) to tighten the nut if the tilt angle cannot be fixed. Fasten the
set screws on the center monitors to fix the tilt angle using Allen Wrench (T-A).
Adjust the height of Center Monitors: Turn the bolt counter-clockwise to lower the center monitors.
Turn the bolt clockwise to raise the center monitors. Use Allen Wrench (T-A).
Set Screw
T-A
T-B
T-A
Adjust the height of the Side Monitors: Remove Nut (I) and turn the bolt counter-clockwise to raise
the monitor. Use Allen Wrench (T-A).

7
STEP 7
STEP 8
To adjust arm joint tension, remove the monitor arm cover and turn the screw underneath with the
Allen Wrench (T-A).
Use Wire Clips (J) to help manage wires.
T-A
J

LAST UPDATED: 08/23/2021
REV2.2
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303