Vivo Mount-E-FD55 User manual

Remote Contro for T Ceiin
Mount
User Guide
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
- -Mode MOUNT  FD55
Remote Control Press and hold for seconds.
Operatin Instructions
Plug the mount in. The buzzer on the mount will beep once.
Step 
Reset tilt angle.
IF MOUNT IS INSTALLD ON A PITCHD SURFAC
Press and release to return the TV ceiling mount flat against the
ceiling surface. The system will beep once, then return the TV
ceiling mount flat against the ceiling surface.
Step 2
Repeat four times. The system will automatically find the
correct position, and it will automatically stop at the maximum
position.
Step 
Step 2
1

To recall Location 2, press and release the button, then press
the button. After the buzzer sounds once, the TV ceiling
mount will automatically adjust to Location 2.
Reca Memory
BUTTON FUNCTIONS
Downward movement
Upward movement
Memory button : Press and hold for seconds, the
buzzer will beep twice. Location is saved.
Memory button 2. Press and hold for seconds, the
buzzer will beep twice. Location 2 is saved.
Stop button
To recall Location 1, press and release the button, then press
the button. After the buzzer sounds once, the TV ceiling
mount will automatically adjust to Location 1.
2
MINIMUM POSITION: To adjust TV mount to minimum position
(resting against the ceiling), simply give it a slight push. The mount
will automatically return to minimum position.
Manua Position Adjustment
MAXIMUM POSITION: To adjust TV mount to maximum position
(lowered completely), follow above instruction to return it to
minimum position. Once in the minimum position, give it a slight
push. The mount will automatically lower to maximum position.
LARN MOD Operatin Instructions
The TV ceiling mount will become unusable if the remote is
lost, so a TV remote may be programmed to control the
mount as a backup in case the original remote is lost (ONLY
works for IR type remotes from popular brands; compatibility
with all remotes is not guaranteed).
NOTE:
TV remote can't operate all functions of the original remote
control. Only basic UP, DOWN, and STOP functions will be
available.
Please follow the steps below when using a TV remote to
control the ceiling mount. Select alternate buttons from the
TV remote that do not directly control the TV.
If you need to erase all learned functions, press and hold ( 1 )
for 4 seconds on the original remote and repeat times. If
the functions are not erased, any new button function learned
will overwrite the last function learned.

LARN MOD
STEP 1: Press and hold (SET) for seconds until
the LED light on the original remote control stays
on, and then press (OK). The mount will beep
once, and the red LED light on the IR received
will stay on to indicate the mount has entered
LEARN MODE.
STEP 2: To learn the ( ) function, press the ( )  
button on the original remote until the mount
beeps twice. The light on the IR received will
change from being constant to a slow flash.
STEP 3: Aim the TV remote at the IR receiver, and
press the button on the TV remote you would
like to set as the ( ) function until the mount 
beeps three times. The light on the IR receiver
will change from a slow flash to a quick flash.
STEP 4: Press the (OK) button on the original
remote until the mount beeps four times. The
light on the IR receiver will turn off, and the ( ) 
function will be learned successfully. If the
mount only beeps once, then the learn function
has failed (indicating that the TV remote may not
be compatible with the TV ceiling mount).
(Please also follow steps 1 through 4 to program
other functions. All 3 functions must be
programmed before operating mount with
programmed TV remote.)
Learn "Power" button on the T remote
Press and hold the (SET) button for seconds until the
LED light on the original remote stays on, then press (OK).
The mount will beep once, and the red LED light on the
IR receiver will stay on. Press and hold the ( 1 ) button on
the original remote until the mount beeps twice, then
release the button. The light on the IR receiver will
change from being constant to a slow flash.
Aim the TV remote at the IR receiver and press the
"Power" button on the remote. The mount will beep
three times. The light on the IR receiver will change from
a slow flash to a quick flash. Press the (OK) button on the
original remote until the mount beeps four times. The
light on the IR receiver will turn off. The "Power" button
will be learned successfully. If the "Power" button is
pressed, the TV ceiling mount will automatically reset.
NOTE: When there is no activity for over 20 seconds in
any step, the TV ceiling mount will automatically exit from
LEARN MODE.
If the TV ceiling mount operates abnormally, it may
be necessary to perform a reset of the mount. To
reset the TV ceiling mount, press and hold the ( 1 )
button on the original remote for seconds (the
light on the remote will turn constant), and repeat
times. The TV ceiling mount will then cycle up
and down to determine correct positions. Once
the mount has stopped moving, press OK on the
remote to complete the reset process.
RST
3

Last updated: 07/11/2018
Safety Warnin
If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by improper
mounting, incorrect assembly, or inappropriate use.
Contact us at
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
Probem Soution
Remote
Control range
is too short
Replace the batteries. If the problem is not resolved, please
contact us to replace the remote control and IR receiver.
Abnormal
operation
Reset the system by following instructions. If problem is not
resolved, contact us to replace the product.
Mount will not
operate
Ensure power supply is properly connected to the product. If so,
ensure power outlet is working. If there is no beeping sound or
red light (power indication) on the TV mount, please contact us to
replace the power supply.
Abnormal
noise Please contact us to replace the product.
Troubeshootin Guide
4