ViziT BVD-403CPO User manual

BVD 3CPO
FEATURES
NOTE.
SAFETY INSTRUCTIONS
12 V
-40
OPERATING INSTRUCTION
is intended for operation with video monitors
Illuminated door bell button
Call sounds in the monitor, when the door bell button is pressed
Door zone video monitoring
IR illumination for the camera
The doorstation has no audio circuits, and does not provide for intercom
The product does not contain voltage above .
Do not make any connections or repair, when the power is on.
Take care not to spill any liquids or chemically active substances on the product.
Switch the power off before cleaning the product. Clean by wiping with dry soft cloth. Do not use any liquid cleaners,
aerosol cleaners or abrasive agents.
.
·
·
·
·
Doorstation as a video door bell and surveillance
device.
The doorstation integrates a door bell button and colour camera with IR illumination in a vandal-proof
case.
BVD VIZIT
BVD-403CPO
-403СРО
BVD CPO-403 Skew base Operating Instruction
x1 x1
PARTS LIST
x1
Fasteners
Screw 40- 4х
Screw 6М4х1
x2 x2 x2
Gag
x 4
Anchor 6x40
4Illuminated ring
3Doorbell button
2LEDs for illumination
1Camera
1
2
3
4
www. 5BVD-403CPO Operating Instruction (revision 12)vizit-group.com 41/201 -

INSTALLATION ORDER
The doorstation is mounted on a wall near your entrance door. The skew base provides 20 turn, and allows either left-
side or right-side mounting
Mounting on the right from the entrance door is performed in the same manner.
°
.
For qualified installation, wiring and servicing refer to technical and commercial partners of VIZIT TM.
The list of companies is given on VIZIT.EU ( .http://vizit.eu/eurounion/)
Figure 2 Doorstation wall-mounting on the left from the entrance door-
Fasteners are supplied.
Figure 3 Doorstation wall-mounting on the right from the entrance door-
Еc
GND
VO
-
-
-;
Supply voltage for built-in camera
Ground
Video out
- Terminal to connect the Doorstation’s door bell
button to the monitor’s DATA terminal
DATA
www. 5BVD-403CPO Operating Instruction (revision 12)vizit-group.com 2 4/201 -
6
4
5
7
Hole 6 mm in diameter
4 mm deep
()
0
х2
Anchor ( )х2
Screw 40- 4х ( )х2
Gag ( )х2
1
2
3
Doorstation
Skew base
Screw 6М4х1 ( )х2
2
3
1
7
4
5
6
Ec
GND
DATA
VO
Figure 4 Terminals layout and marking-

WIRING DIAGRAM
FUNCTIONAL CHECK AND OPERATING ORDER
Before switching the power on, verify all electric connections.
Turn the power supply unit on
Press the (door bell) button The monitor is ringing, when the door bell button is pressed; image appears on the
monitor’s screen.
Check image on the screen Adjust image brightness, contrast and saturation, if needed.
You can activate door zone video monitoring at any time. For details please refer to the operating instruction on your
monitor.
.
"" .
.
%
34°
50 cm
34°
50 cm
Figure 3 Recommended doorstation position
and camera field of view
-
150
cm
50 cm
80 cm 80 cm
5
cm
0
Locate the doorstation so as to avoid:
-;
.
direct rays of the sun or other sources of light
-direct hit of rain or snow
Figure 6 Doorstation BVD and video monitor- -403CPO VIZIT
LN-
GND
LN+
VI1
+E
DATA
Ec1
Ec2
GND
VI2
VIZIT M 27C-4
VIZIT M C
VIZIT M CM
VIZIT M 56C
- 440
- 440
-4
VIZIT M 1
VIZIT M 1M
VIZIT M 56CM
VIZIT M 57M
-44
-44
-4
-4
GND
VO
Ec
DATA
Doorstation
BVD 403CPO-
Monitor
To doorstation
or commutator
To power supply unit
www. 5BVD-403CPO Operating Instruction (revision 12)vizit-group.com 3/4201 -

SPECIFICATIONS
VDC
. W max.
1 x 1 x 40
.3 kg
.kg
OPERATING CONDITIONS
-+
+
Operating voltage from video monitor:
Power consumption:
Dimensions (W)x(H)x(D):
Weight
Weigh with package
The built-in camera parameters are given below:
Ambient temperature range to
Relative humidity of air: up to at
12
1 5
515
0
0 4
30°C 45°C
98% 25°C
± 10%
:
:
:
Camera Parameters
Lens
Angle of view (diagonal)
Colour system
Scanning system
Resolution
Minimal illumination
PAL
СCIR
700 TVL
0 Lux (IR LED ON
0.5 m range)
,
Pinhole
90°
Output voltage 1 Vp-p at hm75 О
Day-Night feature YES
www. 5BVD-403CPO Operating Instruction (revision 12)vizit-group.com 4 4/201 -