Volonic VALET 3 User manual

VA L E T 3
USER MANUAL

2
VA L E T 3 -OVERVIEW
Product overview
1. Charging surface (gray surface in image)
2. USB-C input port
3. LED indicators
4. Rubber legs
Specification:
•Dimensions – 23 x 13.5 x 1.45cm (9.05 x 5.32 x .57in)
•Weight – 692grams (1.5lbs)
In The Box:
•Volonic Valet 3
•Volonic 36W USB-C PD wall charger
•Volonic 6FT (1.8m) USB-C to USB-C cable
•Authenticity / registration card
LED characteristics:
•LED on solid – Device detected and charging
•LED blinking – Unidentified object detected on charging surface, remove device and try again
•All 3 LED’s blinking – Contact our support team at concierg[email protected] or 1-833-VOLO-100
FRONT
BACK
#3 –LED Indicators
#2 -USB-C Port
#1 –Charging surface
#4 –Rubber legs

How to use:
1. Remove giftbox from sleeve
2. Open giftbox to unveil your beautiful Volonic Valet 3
3. Under your Valet 3 is an envelope with your Authenticity card and unique serial number
1. To register your device, scan the QR code on the back of your authenticity card tray
2. Enter last 6 digits of serial number
4. Remove authenticity card tray to access provided wall charger and cable
5. Plug USB-C wall charger into your power outlet
6. Attached USB-C cable into wall charger, make sure a ”click” sound is heard
7. Plug other end of the USB-C cable into your Valet 3, make sure a “click” is heard
8. All 3 LED’s on your Valet 3 should cycle on, then off
9. Now enjoy the freedom of being able to wirelessly charge your device anywhere on the top surface
For frequently asked questions, please visit
https://volonic.com/pages/faqs
If additional assistance is needed, please reach out to our support team at
[e-mail]
or
1-833-VOLO-100
3
“Click”
“Click”
VA L E T 3 –USER MANUAL
SERIAL N
8656612_V3_000001
Scan
SERIAL N
8656612_V3_000001

Housing
•To clean use a soft cloth (cotton or microfiber) and gently wipe clean
•Spray glass cleaner onto soft cloth (cotton or microfiber) and gently wipe
•Do NOT spray directly on to product
•Do NOT use ammonia or bleach-based cleaners
To p p l a t e
•Alcantara®
•It is sufficient to dust Alcantara®using a soft brush, a dry cloth, a lint roller, or a vacuum cleaner.
•After having dusted Alcantara®, run a slightly moistened white cotton cloth over it. Avoid the use of printed absorbent cloths/papers as they can release ink
onto the material.
•For stains; act immediately (within 30 minutes) and begin treating the stain from the outside edge into the center in order to avoid the stain spreading
•Never apply a cleaning product directly onto Alcantara®
•For liquids, use non-printed absorbent paper or a sponge
•Avoid rubbing to prevent the stain from spreading or going deep into the material
•Use a white cloth or a well wrung sponge for the removal of the stains; if you use a sponge, rinse it in clean water and wring it well between each wipe.
•Leather
•To clean use a lightly damp soft cloth (cotton or microfiber) and wipe clean
•For a deeper clean
•mix a solution of warm water and dish soap
•Dip a portion of a soft cloth into the solution, wring cloth to remove excess water, and wipe surface.
•Use second clean damp cloth with only warm water to wipe soap off
•Dry surface by using dry towel and dabbing
•Do NOT use ammonia or bleach-based cleaners
Warning
•Keep liquids away from product and ports
•Do not disassemble your Valet 3
If you have any questions or concerns contact our support team at [e-mail] or 1-833-VOLO
4
VA L E T 3 –PRODUCT CARE