Volt VAL-2015-BBZ User manual

INSTALLATION INSTRUCTIONS
VOLT®LOW VOLTAGE LANDSCAPE LIGHTING
VOLT®Mini Brass Spotlight (Bronze)
ITEM: VAL-2015-BBZ
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT®Mini Brass Spotlight (Bronze) - VAL-2015-BBZ
INSTALLATION INSTRUCTIONS
IMPORTANT: PLEASE READ BEFORE INSTALLATION
!
IMPORTANT SAFETY INSTRUCTIONS
!
813.978.3700 • [email protected] • www.voltlighting.com
2
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that
are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage
lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

PACKAGE CONTENTS
PRODUCT DIMENSIONS
REMOVE GLARE GUARD
1
A. (1) Fixture Body
813.978.3700 • [email protected] • www.voltlighting.com
3
PARTS REQUIRED
A. Mounting Accessory
B. MR11 Lamp
2.76”
1.65”
0.54”
Loosen the set screw and
remove the glare guard from the
xture.
Glare Guard
Fixture Body
Set Screw

2
3
VOLT®Mini Brass Spotlight (Bronze) - VAL-2015-BBZ
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
4
Install MR11 Lamp
Insert the MR11 lamp
with correct wattage and
type marked on xture
label.
CAUTION: Do not ex-
ceed maximum wattage
marked on luminaire
label.
Fixture Socket
MR11 Lamp
Install Glare Guard
Place the glare guard
back onto the xture and
secure with previously
removed set screw.
Glare Guard
Set Screw
Fixture
4
Install Stake
Determine the desired location for
mounting the xture. Hammer the
stake into the ground until ange of
stake is ush to grade. To avoid dam-
age to the stake, place a board on top
of the stake while hammering.
NOTE: If the ground is hard and the
stake is difcult to install, make a
crosscut in the ground using a at
shovel.
Board
Stake
Ground
Soil

5
6
813.978.3700 • [email protected] • www.voltlighting.com
5
Install Fixture to Stake
Clear away an area in the ground
at the wireway slot on top of the
stake. Lay the luminaire pigtail
into the wireway slot and screw
the xture on to the stake. Tight-
en until snug.
Wireway Slot Fixture
Stake
Pigtail
Wire Connection
Strip both the leads from the luminaire pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
Main supply Cable
Wire Connectors
Pigtail

Specications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • www.voltlighting.com
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)