Volt VFL-4001-LI-ABZ User manual

VOLT®Landscape Lighting
LED 120V Floodlights - Yoke Mounted
VFL-4001-LI-ABZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2017, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

LED 120V Floodlights - Yoke Mounted
VFL-4001-LI-ABZ
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
!
!
www.voltlighting.com
- 2 -
1. This LED Floodlight uses the latest in solid state lighting technology for
long life, low maintenance, and high eciency.
2. An internal power-factor-corrected switch mode supply allows this
xture to be used from any nominal 100V-277V, 60Hz AC supply without
any variation in light output.
3. Suitable for use in:
a. Ambient Temperatures of: -20~+40°C (-4~+104°F)
a. Wet Locations
Note: Save these instructions for future reference.
To avoid the risk of re, explosion, or electric shock, this product should
be installed, inspected, and maintained by a qualied electrician only, in
accordance with all applicable electrical codes.
To avoid electric shock:
1. Be certain electrical power is OFF before and during installation and
maintenance.
2. Luminaire must be connected to a wiring system with an equipment-
grounding conductor.
To avoid explosion:
1. Make sure the supply voltage is the same as the rated luminaire voltage.
2. Do not install where the marked operating temperatures exceed the
ignition temperature of the hazardous atmosphere.
3. Do not operate in ambient temperatures above those indicated on the
luminaire.
For supply connections use wire rated for at least 90°C (194°F).
Warning: these luminaire should ONLY be installed by a qualied electrician.

Package Contents
Products Model #
A. (1) Lampbody
[email protected] • 813.978.3700
- 3 -
Model Input Voltage Power
Factor Watt Input Current Mounting
VFL-4001-LI-ABZ 100-277 Volts ≥ 0.95 10W 0.3A Yoke
Product Dimensions
5.5”
3.25” 4.75”
4.5”
1.75”
2.5”
Ø0.75”
R0.25”
VFL-4001-LI-ABZ

www.voltlighting.com
INSTALLATION INSTRUCTIONS
- 4 -
Mark points for Expansion Bolts
1
Hold the yoke mount of
the xture to your desired
mounting surface. Mark two
points on the wall from the
slot holes of the mount. These
marks will be used for wall
anchor bolts.
Wall
Fixture
Mark
Yoke Mount
Install Expansion Bolts
2
Wall Anchor Bolts
Drill proper holes from the marks on
the wall for the wall anchor bolts.
Insert the wall anchor bolts into
drilled holes. Tighten hex nuts on
the wall anchor bolts until they are
fastened to the wall.
Hole
Wall
LED 120V Floodlights - Yoke Mounted
VFL-4001-LI-ABZ

[email protected] • 813.978.3700
- 5 -
Install Lampbody
3
Remove the hex nuts and washers
from wall anchor bolts. Attach the
yoke mount of the xture to the wall
anchor bolts and secure it in place
with the previously removed washers
and hex nuts. Tighten until snug.
Fixture
Bolt
Wire Connections
4
Lampbody
Wiring Terminal
Main Supply Cable
Yo ke
Hex Nut
Washer
Wall
Supply Wire
from Lampbody
Allow enough wire from the lampbody for adjustment purposes.
Connect wires from the xture into the wiring terminal. The white wire
goes to the “Neutral” terminal;the black wire goes to the “Live” terminal;
and the green wire goes to the “Ground” terminal. Fix them in place with
the connector screws.