Volt VPL-1048-4-BBZ User manual

VOLT®Low Voltage Landscape Lighting
VOLT®G2 Arch Brass Path & Area Light
VPL-1048-4-BBZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2021, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

Important: Please Read Before Installation
INSTALLATION INSTRUCTIONS
!
www.voltlighting.com
Important Safety Instructions
!
- 2 -
G2 Arch Brass Path & Area Light
VPL-1048-4-BBZ
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors that
are suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.

[email protected] • 813.978.3700
- 3 -
Package Contents
A. (1) Fixture Body
Product Dimensions
Parts Required
A. (1) Mounting Accessory
B. (1) GU4 Bi-Pin
24.43”
3.39”
5.44”
11.81”

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 4 -
Remove Lens
Install Bulb
Install Lens
1
2
3
G2 Arch Brass Path & Area Light
VPL-1048-4-BBZ
Loosen the lens and remove it
from the xture body.
Fixture Body
Lens
Insert the bulb with the correct
wattage and type marked on the
xture label and push into place.
CAUTION: Do not exceed
maximum wattage marked on
xture label.
Socket
Bulb
Thread the lens back onto the
xture body and hand tighten
until snug.
Fixture Body
Lens

[email protected] • 813.978.3700
- 5 -
Install Stake
4
Install Fixture Body to Stake
5
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake
is ush to grade. To avoid
damage to the stake, place a
board on top of the stake while
hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake
Pass the supply wires through
the center hole of the stake
and thread the stem onto
the stake. Hand tighten until
snug. Clear away an area in
the ground and lay the supply
wires into the wireway slot.
Ground
Stem
Supply Wires
Soil
Stake

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 6 -
Wire Connections
6
Adjust Shade Direction
7
G2 Arch Brass Path & Area Light
VPL-1048-4-BBZ
Strip both leads from the xture wires. Using two UL listed wire
connectors (sold separately), connect the leads from the xture wires to
the main supply cable leads.
Main Supply Cable
Fixture Wires
Wire Connectors
There are two methods to adjust the shade direction.
NOTE: Do not rotate the shade a full 3600. This will damage the internal
wiring.
A. Loosen the knuckle on the stem to adjust the shade to your desired
angle. Once your desired angle is achieved, hand tighten the knuckle
to secure the shade direction.
B. Using the Allen wrench, loosen the set screw on the stem and adjust
the shade to your desired angle. Once your desired angle is achieved,
tighten the set screw using the Allen wrench to secure the shade
direction.
Shade
Shade
Knuckle Allen Wrench Set Screw
ROTATE
OPTION A OPTION B
ROTATE

[email protected] • 813.978.3700
- 7 -
Install/Replace Bulb
Reverse Step 2 - Step 3 to expose the bulb and replace it with the correct
wattage and type marked on the xture label. Then, reinstall the lens.
IMPORTANT: The bulb must be protected from moisture and dust at all
times. Always reinstall the lens when removed.

- 8 -
Specications and product details subject to change without notice.
© Copyright 2021, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
IS-VPL-1048-4-BBZ.pdf
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)