Volt VDL-600 Series User manual

VOLT®Low Voltage Landscape Lighting
VOLT® Deck Light Cast Brass
VDL-600 and VDL-6000 Series
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT®Deck Light Cast Brass
VDL-600 and VDL-6000 Series
INSTALLATION INSTRUCTIONS
www.voltlighting.com [email protected] • 813.978.3700
Package Contents
A. (1) Luminaire
B. (2) Lock Screws
Product Dimensions
Pro Technique for Hiding Lead Wire
Pro Technique for Hiding Splice Connections
Important: Please Read Before Installation
IMPORTANT SAFETY INFORMATION
!
!
This luminaire is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instructions may
result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more
from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer) rated
maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that are suitable for
outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6
inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6 inches (152
mm).
7. If additional lengths of low voltage cable are required, please contact www.
voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage
lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
2”
2 1/4”
3 3/8”
Determine the location for the xture. Drill a hole straight through
the desired mounting location and run the lead wire out the
backside of the location so that the wires are not visible from the
front side. Use a matching trim piece and cut a groove in the back
of trim. Cover the lead wires with the matching trim piece.
All xtures come with 4’ of lead wire enabling you to hide the splice
connections out of sight. If you must make a splice connection in view,
use an inline heat shrink style connection that is less visible than
traditional twist caps.

INSTALLATION INSTRUCTIONS
www.voltlighting.com [email protected] • 813.978.3700
VOLT®Deck Light Cast Brass
VDL-600 and VDL-6000 Series
Install Bulb
Install Lens Assembly
4
5
Insert the bulb with correct wattage and
type marked on the luminaire label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare
hands. Use soft cloth to handle bulb.
Push the lens assembly back onto the
base aligned with the gaps on the
base. Push hard (moisture proof xture
requires force to get air out). Once the
lens assembly is ush with the base,
rotate the lens assembly until it stops
and locks into place.
Inner Shield
Luminaire
Base
Gap
Wire Connector
Main Supply Cable
Install/Replace Bulb
Rotate the lens assembly and then remove it to expose the bulb and replace
it with the correct wattage and type marked on the luminaire label. And
then reinstall the lens assembly.
IMPORTANT: Halogen bulbs must be protected from moisture and dust at all
times. Always reinstall lens assembly when moved.
Pigtail
Install Base
2
Base
Lock
Screw
Wall Anchor
Rotate the lens assembly counter
clockwise until it is stops and then
lift the lens assembly straight off.
Note: The rst time it may be
difcult because the luminaire has
a tight o-ring seal and a grease
sealant for moisture protection.
Attach the base onto the desired
location and secure with the lock
screws.
Note: Wall anchors are required for
certain installation conditions (e.g.
Brick wall, Concrete Wall, etc.).
Mark on the wall for wall anchors
from the holes on the base.
Remove the base and drill proper
holes on the wall and then insert
the wall anchors.
Remove Lens Assembly
1
Luminaire Lens Assembly
Base
Wire Connections
3
Strip both leads from the luminaire
pigtail. Using two wire connectors
(sold separately), connect the leads
from the luminaire to the main supply
cable leads.
Socket
Bulb

is-VDL-6XXX-ver5.pdf
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)