Volt VAL-180 User manual

INSTALLATION INSTRUCTIONS
VOLT®LOW VOLTAGE LANDSCAPE LIGHTING
VOLT® Top Dog Scotty Cast Brass Spotlight
ITEM: VAL-180
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT® Top Dog Scotty Cast Brass Spotlight VAL-180
INSTALLATION INSTRUCTIONS
IMPORTANT: PLEASE READ BEFORE INSTALLATION
!
IMPORTANT SAFETY INSTRUCTIONS
!
813.978.3700 • [email protected] • www.voltlighting.com
2
This luminaire is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and
instructions
may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more
from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer)
rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6
inches (15.2 cm) from a building structure, a luminaire or fitting.
6. The main low voltage cable is intended for shallow burial - less than 6 inches
(152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when
turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from
skin may damage lamp.
6. Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS

PACKAGE CONTENTS
PRODUCT DIMENSIONS
INSTALL STAKE
1
813.978.3700 • [email protected] • www.voltlighting.com
3
PRODUCT DIMENSIONS
A. (1) Fixture Body
A. Mounting Accessory
B. MR16 Lamp
5.67”
2.4”
1.0”
Determine the desired location for
mounting the stake mount. Hammer
the stake into the ground until ange
of stake is ush to grade. To avoid
damage to the stake, place a board
on top of the stake while
hammering.
Note: If the ground is hard and the
stake is difcult to install, make a
crosscut in the ground using a at
shovel.
Board
Stake
Soil
Ground

INSTALL FIXTURE BODY TO STAKE
2
3
VOLT® Top Dog Scotty Cast Brass Spotlight VAL-180
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
4
Clear away an area in the ground
at the wireway slot on top of the
stake. Lay the supply wires into
the wireway slot and attach the
xture on to the stake. Tighten
until snug.
Fixture
Body
Ground
Wireway
Slot
Stake
Supply
Wires
Wire Connection
Strip both the leads from the luminaire pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
Pigtail
Wire Connectors
Main Supply
Cable

4
5
6
813.978.3700 • [email protected] • www.voltlighting.com
5
Remove Glare Guard and Lens
Install MR16 Lamp
Install Glare Guard and Lens
Unlock the set screw and
remove the glare guard from
the lens. Unscrew the lens to
remove it from xture.
Glare Guard
Set Screw
Fixture
Lens
Insert MR16 bulb with the cor-
rect wattage and type marked
on the xture label and secure
into place.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
Socket
Fixture
MR16 Lamp
Thread the lens back onto the
xture and hand tighten. Place
the glare guard back onto the
lens and secure with previously
removed set screw.
Lens
Glare Guard
Set Screw
Fixture

7
VOLT® Top Dog Scotty Cast Brass Spotlight VAL-180
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
6
Adjust Luminaire Direction
ROTATE Loosen the adjustment screw at
the joint and adjust the
luminaire to the desired
direction. Once the desired
direction is achieved, tighten the
adjustment screw.
Adjustment Screw
Luminaire

813.978.3700 • [email protected] • www.voltlighting.com
7

Specications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • www.voltlighting.com
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)