VQ Model FLY BABY User manual

Radio control model
R/C Flugmodell
MONTAGEANLEITUNG
INSTRUCTION MANUAL
SPECIFICATIONS
Wingspan 1210mm (49in.)
Length 880mm (34.6 in.)
Electric Motor (See next page)
Radio 4 Channel / 4 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
TECHNISCHE DATEN
Spannweite 1210mm
Lange 880 mm
Elektroantrieb (siehe nächste Seite)
Fernsteuerung 4 Kanal / 4 Servos
FLY BABY
U.S.MAIL
U.S.MAIL
VERSION
Item No. 1600133

.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
1.5mm
AB
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
CA
Cyanoacrylate Glue
Sekundenkleber
Tool Required/ Empfohlenes Werkzeug
The pre-covered film on ARF kit may wrinkle due to variations of temperature.
Store model in a cool and dry place for awile.
Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.
Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten
werfen z.b bei zu starker Sonnenenstrahlung oder Hitze.
Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach
konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.
!
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
4 - channel radio
RECOMMENDED ACCESSORIES (Purchase separately)
4 - Kanal
Fernsteuerung
Empfohlenes Zubehör (Nicht im Lieferumfang enthalten)
Extension cord
Servoverlangerungskabel
LHS Electronics LS-11D
BB MG Micro servo Digital
Servo:
Li-po Battery:
11.1v, 2600mAh
Brushless Motor:
2814/06 Hobby People
Hobby People ESC
Brushless, 40A
2-6S Li-Po

Cut away only
the covering both side
Cut away only
the covering both side
! Securely glue together If coming off during fly,
you lose control of your air plane.
BB’
1C
slots in the trailing edge of the horizontal stabilizer.
There should be a minimal hinge gap.
-When satisfied with the and alignment, hinge the
elevator to the horizontal stabilizer using thin CA
glue. Make sure to apply a thin layer of CA glue to
the top and bottom of both hinges and to inside the
hinge slots.
-Push the elevator and its hinges into the hinge
Hinge STABILIZER
1TOP VIEW / Draufsicht
CA
Thin CA
1A -Trial fit the horizontal stabilizer in place .
Check the alignment of the horizontal stabilizer.
When you are satisfied with the alignment, use
a pencil to trace around the top and bottom of
the stabilizer where it meets the fuselage.
-Remove the horizontal stabilizer from the
fuselage. Using the sharp hobby knife, carefully
cut away the covering inside the lines which
were marked above, do not cut the balsa.
-Install the horizontal stabilizer into the fuselage
and adjust the alignment as described in first
steep.
-Fill the thin CA glue onto the top and bottom of
the horizontal stabilizer along the area where the
covering was removed and to the fuselage where
the horizontal stabilizer mounts.
CA
Thin CA
CA
Thin CA
Plastic control horn
.....................1
Note: The rectangular hole on the elevator for the
elevator control horn installation is pre-cut at factory.
CA
Thin CA
CA
Thin CA
1A
1B
1D
1B -Trial fit the vertical stabilizer in place .
Check the alignment of the vertical stabilizer.
When you are satisfied with the alignment, use a
pencil to trace around the right and left of the
stabilizer where it meets the fuselage.
-Remove the vertical stabilizer from the fuselage.
Using the sharp hobby knife, carefully cut away the
covering inside the lines which were marked above,
do not cut the balsa.
-Install the vertical stabilizer into the fuselage and
adjust the alignment as described in first steep.
-Fill the thin CA onto the right and left of the vertical
stabilizer along the area where the covering was
removed and to the fuselage where the vertical
stabilizer mounts.
90O90O
A=A’
Cut away only
the covering
Thin CA
1C
CA
Tail wheel gear

............4
3x15mm screw
All holes pre-drilled
at factory
4x30mm screw
4mm Washer
4mm Nut
......2
.......................4
......................4
3
4mm nut
4x30mm screw
Aluminum landing
gear
3A
Finish
All blind-nuts assembled
as factory
3x15mm
4x30mm
3B
3B
3B
Pull the magnetic top hatch out
of the fuselage ( full the rear of
the hatch as shown)
5/64”
2mm
5/64”
2mm
5/64”
2mm
CA
3x15mm 3x10mm
3mm dia.
...4 ...4 ...4
4
BOTTOM - VIEW / Unteransicht
Thin CA
Tail wheel gear
CA
A=1.2”(37mm)
A
5/64”
2mm
Cut away only
the covering
Note: The rectangular hole on the rudder
for the rudder control horn installation is
pre-cut at factory.
Note: Making sure that you drill
the hole perpendicular to the
leading edge of the rudder.
2A
2B
2
Plastic control horn
.....................1
2mm collar...1
25mm ..........1
CA
Thin CA

5
Cut away only
the covering
BOTTOM - VIEW / Unteransicht
Adhesive
tape
1-Connect the 30cm extension (not include) to the aileron servo and secure with the adhesive tape.
2-Using the thread (pre-installed at factory), full the extension out of the wing as shown.
3-Attach the aileron servo into the wing.
4-Attach the aileron control horn using CA glue.
Do the same way with second wing half.
Note: The rectangular hole on
the aileron for the aileron control
horn installation is pre-cut at
factory.
Cut away only
the covering
CA
Thin CA
Plastic control horn
.....................2
CA
6
........4
Thin CA
The holes are Pre-cut
at factory
Cut away only
the covering
TOP VIEW / Draufsicht
Do the same way with another half wing.
7
TOP VIEW / Draufsicht
1mm dia. Cable
...1 roll
2mm metal tube
.....................4
210mm (8.2”)
7A 7B 7C
........2

CA
CA
Thin CA
Thin CA
9
10
Note: Attach the wing onto the fuselage
using 6x50mm plastic bolt.
6x50mm plastic bolt
....1
8
Fuselage - Right view Fuselage - Left view
Elevator servo Rudder servo
Note: The rectangular holes on each side of the fuselage for the rudder and elevator servo installation are pre-cut at factory.
Cut away only the covering.

21/64”
(8mm)
7/16”
(11mm)
1”(25mm)
AILERON STROKE ELEVATOR STROKE RUDDER STROKE
21/64”
(8mm)
7/16”
(11mm) 1”(25mm)
Control surface / Ruderausschlage
11
Querruderausschlag
Hohenruderausschlag
Seitenruderausschlag
CG
WARNING ! Securely install the receiver and power
pack, ensuring they will not come loose or rattle during
flight.
Never fly before checking the Cg’s required position.
In order to obtain the CG specified, reposition the receiver and power pack
Wing center section
Balance / Schwerpunkt
IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass-
cleaner to clean on surface of your model to keep the colour not fade.
12
Uberprufen Sie vor dem Flug den Schwerpunkt.
2 3/8”-2 5/8”
60mm-65mm