Wacker Neuson P 35A User manual

Operator’s Manual
Wet Screed
P35A
Type P35A
Document 5000192669
Date 0818
Revision 06
Language EN
5000192669

Copyright notice © Copyright 2018 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: [phone] · Fax: [phone] · Tel: [phone]
www.wackerneuson.com
Original instructions This Operator’s Manual presents the original instructions. The original
language of this Operator’s Manual is American English.

CALIFORNIA Proposition 65 Warning
wc_tx004643en.fm 3
CALIFORNIA Proposition 65 Warning
WARNING
The engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
WARNING
Diesel engine exhaust and some of its constituents are known to the State of
California to cause cancer, birth defects, and other reproductive harm.
WARNING
Cancer and Reproductive Harm -
www.P65Warnings.ca.gov.
WARNING
Batteries, battery posts, terminals and related accessories contain lead and lead
compounds, and other chemicals known to the State of California to cause cancer
and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

CALIFORNIA Proposition 65 Warning
wc_tx004643en.fm
4
Notes

wc_tx003251gb_FM10.fm 5
P 35A Foreword
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machines
covered in
this manual
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine
documentation
■From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
■Keep a copy of the Operator’s Manual with the machine at all times.
■For spare parts information, please see your Wacker Neuson Dealer, or visit the
Wacker Neuson website at http://www.wackerneuson.com/.
■When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Machine Item Number
P 35A 0620956, 0620957, 0620958
wc_gr010231
Serial Number:

wc_tx003251gb_FM10.fm
6
Foreword P 35A
Expectations
for
information in
this manual
■This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
■Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
■The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change any
portion of this information without notice.
■The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
CALIFORNIA
Proposition
65 Warning
Combustion exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental
discharge of sparks or flames from the engine exhaust. Spark arresters are
qualified and rated by the United States Forest Service for this purpose. In order to
comply with local laws regarding spark arresters, consult the engine distributor or
the local Health and Safety Administrator.
Manufacturer’s
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
■Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
■Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
■Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
■Serious injury hazards to the operator and persons in the work area
■Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.

Original Declaration of Conformity
2016-CE-P35A_en_FM10.fm
EC Declaration of Conformity
Manufacturer
Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,
Menomonee Falls, Wisconsin 53051 USA
Product
Product
Product category
Product function
Item number
P35A
Vibratory Concrete Screed
To level freshly poured concrete
5000620956, 5000620957, 5000620958
Directives and Standards
We hereby declare that this product meets and complies with the relevant regulations and
requirements of the following directives and standards:
2006/42/EC, 2014/30/EU, EN 12649
Authorized Person for Technical Documents
Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6, 85084
Reichertshofen, Germany
Menomonee Falls, WI, USA, 09.05.16
Keith Herr
Vice President and Managing Director
For Wacker Neuson
Scott Grahl
Manager, Product Engineering
For Wacker Neuson
Jeff Volden
Director, Product Engineering
For Wacker Neuson

Table of Contents
P35A
wc_bo5000192669_06TOC.fm 9
CALIFORNIA Proposition 65 Warning 3
Foreword 5
EC Declaration of Conformity 7
1 Safety Information 11
1.1 Signal Words Used in this Manual ..................................................... 11
1.2 Machine Description and Intended Use ............................................. 12
1.3 Operating Safety ................................................................................ 13
1.4 Service Safety .................................................................................... 15
1.5 Operator Safety while Using Internal Combustion Engines ............... 17
2 Labels 18
2.1 Label Locations .................................................................................. 18
2.2 Label Meanings .................................................................................. 19
3 Lifting and Transporting 21
4 Operation 22
4.1 Control / Component Locations .......................................................... 22
4.2 Preparing the Machine for First Use ................................................... 23
4.3 Position of the Operator ..................................................................... 23
4.4 Recommended Fuel ........................................................................... 24
4.5 Before Starting ................................................................................... 24
4.6 Starting ............................................................................................... 25
4.7 Stopping ............................................................................................. 25
4.8 Operation ............................................................................................ 26
4.9 Exciter Adjustment ............................................................................. 28
4.10 Adjusting the Handle Height ............................................................... 29
4.11 Kickstand ............................................................................................ 29
4.12 Emergency Shutdown Procedure ....................................................... 29
5 Maintenance 30
5.1 Maintaining the Emission Control System .......................................... 30
5.2 Periodic Maintenance Schedule ......................................................... 30
5.3 Engine Oil ........................................................................................... 31

Table of Contents P35A
wc_bo5000192669_06TOC.fm
10
5.4 Air Cleaner ..........................................................................................32
5.5 Spark Plug (Wacker Neuson/Honda) ..................................................33
5.6 Cleaning the Machine ..........................................................................34
5.7 Long-Term Storage .............................................................................34
5.8 Troubleshooting ...................................................................................34
6 Technical Data 35
6.1 Engine .................................................................................................35
6.2 Blades .................................................................................................36
6.3 Dimensions ..........................................................................................36
6.4 Sound and Vibration Specifications .....................................................37
7 Emission Control Systems Information
and Warranty 38
7.1 Emission Control Systems Warranty Statement .................................38

wc_si000748gb_FM10.fm 11
P 35A Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
►Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
►To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
►To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
►To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.

wc_si000748gb_FM10.fm
12
Safety Information P 35A
1.2 Machine Description and Intended Use
This machine is a vibratory concrete screed. The Wacker Neuson Wet Screed
consists of a gasoline engine, a fuel tank, a metal blade, an eccentric weight
positioned at the center of the metal blade, and a control handle. The gasoline
engine spins the eccentric weight through a drive shaft, producing vibrations that
travel the length of the metal blade. The operator uses the control handle to pull the
machine across uncured concrete.
This machine is intended to be used for striking off uncured concrete slabs with or
without the support of grade stakes or forms.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
■Using the machine as a ladder, support, or work surface
■Using the machine to carry or transport passengers or equipment
■Engaging the screed when not on uncured concrete
■Operating the machine on non-compactable surfaces, such as asphalt or cured
concrete
■Operating the machine outside of factory specifications
■Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
■Heat, noise, exhaust, and carbon monoxide from the engine
■Chemical burns from the curing concrete
■Fire hazards from improper refueling techniques
■Fuel and its fumes, fuel spillage from improper lifting technique
■Personal injury from improper lifting techniques or operating techniques
■Excessive vibration by holding the blade
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.

wc_si000748gb_FM10.fm 13
P 35A Safety Information
1.3 Operating Safety
Operator
training
Before operating the machine:
■Read and understand the operating instructions contained in all manuals
delivered with the machine.
■Familiarize yourself with the location and proper use of all controls and safety
devices.
■Contact Wacker Neuson for additional training if necessary.
When operating this machine:
■Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
■Have received instruction on how to properly use the machine
■Are familiar with required safety devices
The machine must not be accessed or operated by:
■Children
■People impaired by alcohol, drugs, or prescription drugs
Application
area
Be aware of the application area.
■Keep unauthorized personnel, children, and pets away from the machine.
■Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
■Identify whether special hazards exist in the application area, such as toxic
gases or unstable ground conditions, and take appropriate action to eliminate
the special hazards before using the machine.
■Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Safety
devices,
controls, and
attachments
Only operate the machine when:
■All safety devices and guards are in place and in working order.
■All controls operate correctly.
■The machine is set up correctly according to the instructions in the Operator’s
Manual.
■The machine is clean.
■The machine’s labels are legible.
To ensure safe operation of the machine:
■Do not operate the machine if any safety devices or guards are missing or
inoperative.
■Do not modify or defeat the safety devices.
■Only use accessories or attachments that are approved by Wacker Neuson.

wc_si000748gb_FM10.fm
14
Safety Information P 35A
Safe
operating
practices
When operating this machine:
■Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
■Do not operate a machine in need of repair.
Personal
Protective
Equipment
(PPE)
Wear the following personal protective equipment (PPE) while operating this
machine:
■Close-fitting work clothes that do not hinder movement
■Safety glasses with side shields
■Hearing protection
■Safety-toed footwear
After use ■Stop the engine when the machine is not being operated.
■Close the fuel valve on engines equipped with one when the machine is not
being operated.
■Ensure that the machine will not tip over, roll, slide, or fall when not being
operated.
■Store the machine properly when it is not being used. The machine should be
stored in a clean location out of the reach of children.

wc_si000748gb_FM10.fm 15
P 35A Safety Information
1.4 Service Safety
Service
training
Before servicing or maintaining the machine:
■Read and understand the instructions contained in all manuals delivered with
the machine.
■Familiarize yourself with the location and proper use of all controls and
protective devices.
■Only trained personnel shall troubleshoot or repair problems occurring with the
machine.
■Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
■Do not allow untrained or improperly trained people to service or maintain the
machine. Personnel servicing or maintaining the machine must be familiar with
the associated potential risks and hazards.
Precautions Follow the precautions below when servicing or maintaining the machine.
■Read and understand the service procedures before performing any service to
the machine.
■All adjustments and repairs must be completed before operation. Do not
operate the machine with a known problem or deficiency.
■All repairs and adjustments shall be completed by a qualified technician.
■Turn off the machine before performing maintenance or making repairs.
Machine
modifications
When servicing or maintaining the machine:
■Use only accessories/attachments that are approved by Wacker Neuson.
■Do not defeat safety devices.
■Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing
parts and
labels
■Replace worn or damaged components.
■Replace all missing and hard-to-read labels.
■When replacing electrical components, use components that are identical in
rating and performance to the original components.
■When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
Cleaning When cleaning and servicing the machine:
■Keep machine clean and free of debris such as leaves, paper, cartons, etc.
■Keep labels legible.
When cleaning the machine:
■Do not clean the machine while it is running.
■Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.

wc_si000748gb_FM10.fm
16
Safety Information P 35A
Personal
protective
equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:
■Close-fitting work clothes that do not hinder movement
■Safety glasses with side shields
■Hearing protection
■Safety-toed footwear
In addition, before servicing or maintaining the machine:
■Tie back long hair.
■Remove all jewelry (including rings).
Safe service
practices
■Do not crank a flooded engine with the spark plug removed on gasoline-
powered engines. Fuel trapped in the cylinder will squirt out the spark plug
opening.
■Do not test for spark on gasoline-powered engines if the engine is flooded or the
smell of gasoline is present. A stray spark could ignite the fumes.
■Handle blades carefully. The blades can develop sharp edges which can cause
serious cuts.

wc_si000748gb_FM10.fm 17
P 35A Safety Information
1.5 Operator Safety while Using Internal Combustion Engines
Operating
safety
When running the engine:
■Keep the area around the exhaust pipe free of flammable materials.
■Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine. Do not run the machine if fuel leaks are present or the fuel lines are
loose.
■Do not smoke while operating the machine.
■Do not run the engine near sparks or open flames.
■Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
■Do not operate a machine when its fuel cap is loose or missing.
■Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Refueling
safety
When refueling the engine:
■Clean up any spilled fuel immediately.
■Refill the fuel tank in a well-ventilated area.
■Reinstall the fuel tank cap after refueling.
■Do not smoke.
■Do not refuel a hot or running engine.
■Do not refuel the engine near sparks or open flames.
■Use suitable tools for refueling (for example, a fuel hose or a funnel).
■Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.
Static electricity can ignite the fuel or fuel vapors.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
►Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison.
Exposure to carbon monoxide can kill you in minutes.
►NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through such items as exhaust fans or hoses.

wc_si000749gb_FM10.fm
18
Labels P35A
2 Labels
2.1 Label Locations
C
A
E
D
B
wc_gr008018
F

wc_si000749gb_FM10.fm 19
P35A Labels
2.2 Label Meanings
AWARNING
To reduce the risk of hearing loss and
eye injury, always wear hearing
protection and eye protection when
operating this machine.
B WARNING
Hot surface
C DANGER
Asphyxiation hazard
Engines emit carbon monoxide.
Do not run the machine indoors or in an
enclosed area unless adequate ventila-
tion, through such items as exhaust
fans or hoses, is provided.
Read the Operator’s Manual.
No sparks, flames, or burning objects
near the machine.
Stop the engine before refueling.
DThis machine may be covered by one or
more patents.
178745
178745
STOP
STOP
178715
178715

wc_si000749gb_FM10.fm
20
Labels P35A
EWARNING
Rotating machinery! Do not reach inside
machine when the engine is running.
FCalifornia Proposition 65 Warning
Cancer and Reproductive Harm -
www.P65Warnings.ca.gov.
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
Cáncer y daño reproductivo
www.P65Warnings.ca.gov
Cancer ou malformations
congénitales
www.P65Warnings.ca.gov
WARNING
AVERTISSEMENT
ADVERTENCIA
5100045462