WAGO 750-806 User manual

WAGO-I/O-SYSTEM 750
Manual
750-806
Fieldbus Controller DeviceNet
TM
16-
bit CPU
Version 2.0.0

2 WAGO-I/O-SYSTEM 750
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
© 2015 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]om
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]om
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [e-mail]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.

WAGO-I/O-SYSTEM 750 Table of Contents 3
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
Table of Contents
1Notes about this Documentation................................................................. 8
1.1 Validity of this Documentation................................................................. 8
1.2 Copyright................................................................................................... 8
1.3 Symbols..................................................................................................... 9
1.4 Number Notation..................................................................................... 11
1.5 Font Conventions .................................................................................... 11
2Important Notes ......................................................................................... 12
2.1 Legal Bases ............................................................................................. 12
2.1.1 Subject to Changes............................................................................. 12
2.1.2 Personnel Qualifications..................................................................... 12
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying
Provisions........................................................................................... 12
2.1.4 Technical Condition of Specified Devices......................................... 13
2.2 Safety Advice (Precautions).................................................................... 14
3System Description..................................................................................... 16
3.1 Manufacturing Number........................................................................... 17
3.2 Component Update.................................................................................. 18
3.3 Storage, Assembly and Transport ........................................................... 18
3.4 Assembly Guidelines/Standards.............................................................. 19
3.5 Power Supply.......................................................................................... 20
3.5.1 Isolation.............................................................................................. 20
3.5.2 System Supply.................................................................................... 21
3.5.2.1 Connection..................................................................................... 21
3.5.2.2 Dimensioning................................................................................. 22
3.5.3 Field Supply........................................................................................ 25
3.5.3.1 Connection..................................................................................... 25
3.5.3.2 Fusing ............................................................................................ 27
3.5.4 Supplementary Power Supply Regulations........................................ 30
3.5.5 Supply Example.................................................................................. 31
3.5.6 Power Supply Unit ............................................................................. 33
3.6 Grounding ............................................................................................... 34
3.6.1 Grounding the DIN Rail..................................................................... 34
3.6.1.1 Framework Assembly.................................................................... 34
3.6.1.2 Insulated Assembly........................................................................ 34
3.6.2 Grounding Function............................................................................ 35
3.7 Shielding ................................................................................................. 36
3.7.1 General ............................................................................................... 36
3.7.2 Bus Cables.......................................................................................... 36
3.7.3 Signal Lines........................................................................................ 37
3.7.4 WAGO Shield Connecting System.................................................... 37
4Device Description ..................................................................................... 38
4.1 View........................................................................................................ 40
4.2 Connectors............................................................................................... 42
4.2.1 Device Supply .................................................................................... 42
4.2.2 Fieldbus Connection........................................................................... 43

4 Table of Contents WAGO-I/O-SYSTEM 750
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
4.3 Display Elements .................................................................................... 44
4.4 Operating Elements................................................................................. 45
4.4.1 Service Interface................................................................................. 45
4.4.2 Mode Selector Switch......................................................................... 46
4.4.3 DIP Switch.......................................................................................... 48
4.4.3.1 Baud Rate Setting .......................................................................... 48
4.4.3.2 Station address............................................................................... 49
4.5 Technical Data ........................................................................................ 50
4.5.1 Device Data ........................................................................................ 50
4.5.2 System Data........................................................................................ 50
4.5.3 DeviceNetTM Fieldbus ........................................................................ 51
4.5.4 Power Supply...................................................................................... 51
4.5.5 Accessories......................................................................................... 51
4.5.6 Connection Type ................................................................................ 51
4.5.7 Climatic Environmental Conditions................................................... 52
4.5.8 Mechanical Strength acc. to IEC 61131-2.......................................... 52
4.6 Approvals................................................................................................ 53
4.7 Standards and Guidelines........................................................................ 55
5Mounting..................................................................................................... 56
5.1 Installation Position................................................................................. 56
5.2 Overall Configuration ............................................................................. 56
5.3 Mounting onto Carrier Rail..................................................................... 58
5.3.1 Carrier Rail Properties........................................................................ 58
5.3.2 WAGO DIN Rail................................................................................ 59
5.4 Spacing.................................................................................................... 59
5.5 Mounting Sequence................................................................................. 60
5.6 Inserting and Removing Devices ............................................................ 61
5.6.1 Inserting the Fieldbus Coupler/Controller.......................................... 62
5.6.2 Removing the Fieldbus Coupler/Controller ....................................... 62
5.6.3 Inserting the I/O Module.................................................................... 63
5.6.4 Removing the I/O Module.................................................................. 64
6Connect Devices ......................................................................................... 65
6.1 Data Contacts/Internal Bus ..................................................................... 65
6.2 Power Contacts/Field Supply.................................................................. 66
6.3 Connecting a Conductor to the CAGE CLAMP®................................... 67
7Function Description ................................................................................. 68
7.1 Operating System.................................................................................... 68
7.1.1 Run-up................................................................................................ 68
7.1.2 PFC Cycle........................................................................................... 68
7.2 Process Data Architecture....................................................................... 70
7.2.1 Basic Structure.................................................................................... 70
7.3 Data Exchange ........................................................................................ 71
7.3.1 Communication Interfaces.................................................................. 72
7.3.2 Memory Space.................................................................................... 72
7.3.3 Addressing.......................................................................................... 76
7.3.3.1 Fieldbus-Specific Addressing........................................................ 76
7.3.3.2 Absolute Addressing...................................................................... 78
7.3.3.3 Calculate Addresses....................................................................... 79

WAGO-I/O-SYSTEM 750 Table of Contents 5
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
7.3.3.4 Address Range for I/O Module Data............................................. 79
7.3.3.5 Address Range for Fieldbus Variables .......................................... 79
7.3.3.6 Address Range for Flags................................................................ 79
7.3.3.7 Example for Absolute Addresses................................................... 80
8Commissioning........................................................................................... 81
8.1 Connecting Client PC and Fieldbus Nodes............................................. 82
8.2 Setting the DeviceNet™Station Address and Baud Rate........................ 83
8.3 Configuring Static and Dynamic Assemblies ......................................... 84
9Programming the PFC Using WAGO-I/O-PRO..................................... 95
9.1 Configuring the Fieldbus Controller using the I/O Configurator............ 98
9.2 Libraries for WAGO-I/O-PRO ............................................................. 100
9.3 General Information about IEC Tasks .................................................. 101
9.3.1 IEC Task Sequence........................................................................... 103
9.3.2 Overview of Most Important Task Priorities.................................... 103
9.4 System Events....................................................................................... 104
9.4.1 Enabling/Disabling System Events .................................................. 105
9.5 Transfer the IEC program to the Fieldbus controller............................ 106
9.5.1 Transfer via Serial Service Port........................................................ 107
9.5.2 Transferring an Application via Fieldbus......................................... 110
9.6 Special DeviceNetTM Characteristics of the Fieldbus Controller.......... 111
9.6.1 Establishing a Connection via the UCMM Port............................... 111
9.6.2 Offline Connection Set..................................................................... 111
9.6.3 DeviceNet Shutdown........................................................................ 111
9.6.4 Dynamic Assembly .......................................................................... 111
9.6.5 Change MAC ID by SW................................................................... 112
9.6.6 Heartbeat........................................................................................... 112
9.6.7 Bit-Strobe ......................................................................................... 113
10 Diagnostics................................................................................................ 114
10.1 LED Signaling....................................................................................... 114
10.1.1 Evaluating the Fieldbus Status ......................................................... 115
10.1.2 Evaluating Node Status – I/O LED (Blink Code Table).................. 116
10.1.2.1 USR LED..................................................................................... 123
10.1.3 Evaluating Power Supply Status ...................................................... 124
11 Fieldbus Communication........................................................................ 125
11.1 DeviceNetTM.......................................................................................... 125
11.1.1 Network Structure ............................................................................ 126
11.1.1.1 Transfer Media............................................................................. 126
11.1.1.2 Cabling......................................................................................... 127
11.1.1.3 Topology...................................................................................... 128
11.1.1.4 Network Grounding..................................................................... 130
11.1.1.5 Interface Modules........................................................................ 130
11.1.2 Network Communication ................................................................. 131
11.1.2.1 Objects, Classes, Instances and Attributes .................................. 131
11.1.3 Characteristics of DeviceNetTM Devices.......................................... 132
11.1.3.1 Communication Model................................................................ 132
11.1.3.1.1 Message Groups...................................................................... 132
11.1.3.1.2 Message Types........................................................................ 132
11.1.3.1.2.1 I/O Messages...................................................................... 132

6 Table of Contents WAGO-I/O-SYSTEM 750
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
11.1.3.1.2.2 Explicit Messages............................................................... 132
11.1.3.2 Data Exchange............................................................................. 133
11.1.4 Process Data and Diagnostic Status ................................................. 133
11.1.4.1 Process Image.............................................................................. 133
11.1.4.1.1 Assembly Instances................................................................. 133
11.1.5 Configuration and Parameterization Using the Object Model......... 135
11.1.5.1 EDS Files..................................................................................... 135
11.1.5.2 Object Model ............................................................................... 135
11.1.5.2.1 Object Classes......................................................................... 137
11.1.5.2.1.1 Identity Class (0x01).......................................................... 138
11.1.5.2.1.2 Message Router (0x02) ...................................................... 138
11.1.5.2.1.3 DeviceNet Object (0x03) ................................................... 139
11.1.5.2.1.4 Assembly Object (0x04)..................................................... 140
11.1.5.2.1.4.1 Dynamic Assembly ....................................................... 145
11.1.5.2.1.5 Connection Object (0x05).................................................. 146
11.1.5.2.1.6 Acknowledge Handler Object (0x2B)................................ 152
11.1.5.2.1.7 Coupler Configuration Object (0x64)................................ 153
11.1.5.2.1.8 Discrete Input Point Object (0x65) .................................... 159
11.1.5.2.1.9 Discrete Output Point Object (0x66).................................. 160
11.1.5.2.1.10 Analog Input Point Object (0x67)...................................... 161
11.1.5.2.1.11 Analog Output Point Object (0x68) ................................... 162
11.1.5.2.1.12 Module Configuration Object (0x80)................................. 163
11.1.5.2.1.13 Input Fieldbus Variable (0xA0) ......................................... 164
11.1.5.2.1.14 Input Fieldbus Variable (0xA1) ......................................... 165
11.1.5.2.1.15 Input Fieldbus Variable (0xA2) ......................................... 165
11.1.5.2.1.16 Input Fieldbus Variable (0xA6) ......................................... 165
11.1.5.2.1.17 Input Fieldbus Variable (0xA7) ......................................... 165
11.1.5.2.1.18 Output Fieldbus Variable (0xA8)....................................... 166
11.1.5.2.1.19 Output Fieldbus Variable (0xA9)....................................... 166
11.1.5.2.1.20 Input Fieldbus Variable (0xAA) ........................................ 166
11.1.5.2.1.21 Input Fieldbus Variable (0xAB)......................................... 166
11.1.5.2.1.22 Output Fieldbus Variable (0xAC)...................................... 166
11.1.5.2.1.23 Output Fieldbus Variable (0xAD)...................................... 167
12 I/O Modules.............................................................................................. 168
12.1 Overview............................................................................................... 168
12.2 Process Data Architecture for DeviceNetTM ......................................... 169
12.2.1 Digital Input Modules....................................................................... 169
12.2.2 Digital Output Modules.................................................................... 170
12.2.3 Analog Input Modules...................................................................... 171
12.2.4 Analog Output Modules................................................................... 172
12.2.5 Specialty Modules ............................................................................ 173
12.2.6 System Modules ............................................................................... 193
13 Use in Hazardous Environments............................................................ 194
13.1 Marking Configuration Examples......................................................... 195
13.1.1 Marking for Europe According to ATEX and IEC-Ex .................... 195
13.1.2 Marking for America According to NEC 500.................................. 200
13.2 Installation Regulations......................................................................... 201
13.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX
554086 X)......................................................................................... 202

WAGO-I/O-SYSTEM 750 Table of Contents 7
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
13.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX
106032 X)......................................................................................... 203
13.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)204
13.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN
12.0039 X)........................................................................................ 205
13.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 206
List of Figures.................................................................................................... 207
List of Tables...................................................................................................... 209

8 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
1 Notes about this Documentation
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
1.1 Validity of this Documentation
This documentation is only applicable to the “Fieldbus Controller DeviceNetTM”
(750-806).
The product “Fieldbus Controller DeviceNetTM” (750-806) shall only be installed
and operated according to the instructions in this manual and the system
description for the WAGO-I/O-SYSTEM 750.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the system
description for the WAGO-I/O-SYSTEM 750, which can be downloaded at
www.wago.com. There, you can obtain important information including
information on electrical isolation, system power and supply specifications.
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.

WAGO-I/O-SYSTEM 750 Notes about this Documentation 9
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
1.3 Symbols
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.

10 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).

WAGO-I/O-SYSTEM 750 Notes about this Documentation 11
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
1.4 Number Notation
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
1.5 Font Conventions
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]

12 Important Notes WAGO-I/O-SYSTEM 750
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
2 Important Notes
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
2.1 Legal Bases
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description” > “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.

WAGO-I/O-SYSTEM 750 Important Notes 13
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

14 Important Notes WAGO-I/O-SYSTEM 750
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
2.2 Safety Advice (Precautions)
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.

WAGO-I/O-SYSTEM 750 Important Notes 15
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.

16 System Description WAGO-I/O-SYSTEM 750
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
3 System Description
The WAGO-I/O-SYSTEM 750 is a modular, fieldbus-independent input/output
system (I/O system). The configuration described here consists of a fieldbus
coupler/controller (1) and the modular I/O modules (2) for any signal shapes that
form the fieldbus node together. The end module (3) completes the node and is
required for correct operation of the fieldbus node.
Figure 1: Fieldbus Node (Example)
Fieldbus couplers/controllers are available for different fieldbus systems.
The standard fieldbus couplers/controllers contain the fieldbus interface,
electronics and a power supply terminal. The fieldbus interface forms the physical
interface to the relevant fieldbus. The electronics process the data of the I/O
modules and make it available for the fieldbus communication. The 24 V system
supply and the 24 V field supply are fed in via the integrated power supply
terminal.
The fieldbus coupler/controller exchanges process data with the respective control
via the respective fieldbus. The programmable fieldbus controllers (PFC) allow
implementation of additional PLC functions. WAGO-I/O-PRO is used to program
the fieldbus controllers according to IEC 61131-3.
I/O modules for diverse digital and analog I/O signals as well as special functions
can be connected to the fieldbus coupler/controller. The communication between
the fieldbus coupler/controller and the I/O modules is carried out via an internal
bus.
The components of the WAGO-I/O-SYSTEM 750 have clear termination points,
light emitting diodes for status display, plug-in mini WSB tags and group marker
cards for labeling.
The 1, 2 or 3 wire technology supplemented by a ground wire connection allows
for direct sensor or actuator wiring.

WAGO-I/O-SYSTEM 750 System Description 17
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
3.1 Manufacturing Number
The serial number indicates the delivery status directly after production. This
number is part of the labeling on the side of each component.
In addition, the serial number is printed on the cover cap of the configuration and
programming interface of the fieldbus coupler/controller, so that it can also be
read when installed.
Figure 2: Marking Area for Serial Numbers
There are two serial numbers in two rows in the side marking. They are left of the
release tab. The first 10 positions in the longer row of the serial numbers contain
version and date identifications.
Example structure of the rows: 0114010101…
01
14
01
01
01
(additional positions)
WW
YY
FW --
HW
FL
-
Calendar
week
Year
Firmware
version
Hardware
version
Firmware
loader
version
Internal information
The row order can vary depending on the production year, only the longer row is
relevant. The back part of this and the shorter row contain internal administration
information from the manufacturer.

18 System Description WAGO-I/O-SYSTEM 750
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
3.2 Component Update
For the case of an update of one component, the lateral marking on each
component contains a prepared matrix.
This matrix makes columns available for altogether three updates to the entry of
the current update data, like production order number (NO; starting from calendar
week 13/2004), date stamp (DS), software version (SW), hardware version (HW)
and the firmware loader version (FWL, if available).
Current version data for
1. Update
2. Update
3. Update
Production order no.
NO
only starting from
Date stamp
DS
calendar week 13/2004
Software version
SW
Hardware version
HW
Firmware loader vers.
FWL
only for fieldbus
couplers/controllers
If the update of a component took place, the current version data are registered
into the columns of the matrix.
Additionally with the update of a fieldbus coupler or controller also the cover of
the configuration and programming interface of the fieldbus coupler or controller
is imprinted with the current production order number.
The original manufacturing information on the device's housing remains
unchanged.
3.3 Storage, Assembly and Transport
Whenever possible, the components are to be stored in their original packaging.
Likewise, the original packaging provides optimal protection during transport.
When assembling or repacking the components, the contacts must not be soiled or
damaged. The components must be stored and transported in appropriate
containers/packaging. Thereby, the ESD information is to be regarded.

WAGO-I/O-SYSTEM 750 System Description 19
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
3.4 Assembly Guidelines/Standards
•DIN 60204 Electrical equipping of machines
•DIN EN 50178 Equipping of high-voltage systems with electronic
components (replacement for VDE 0160)
•EN 60439 Low-voltage switchgear and controlgear assemblies

20 System Description WAGO-I/O-SYSTEM 750
750-806 Fieldbus Controller DeviceNetTM
Manual
Version 2.0.0
3.5 Power Supply
3.5.1 Isolation
Within the fieldbus node, there are three electrically isolated potentials:
• Electrically isolated fieldbus interface via transformer
• Electronics of the fieldbus couplers/controllers and the I/O modules
(internal bus)
• All I/O modules have an electrical isolation between the electronics
(internal bus, logic) and the field electronics. Some digital and analog input
modules have each channel electrically isolated, please see catalog.
Figure 3: Isolation for Fieldbus Couplers/Controllers (Example)