WAHLAP TECH PUSHING POINTS User manual

Please keep this manual properly for convenient reference as needed.
For safety reasons, please read the manual first before plugging in machine.
Ver.1.00

Table of Contents
About This Manual
1. Safety Precautions
2. Product Description
3. Game Description
1.1 Warning Stickers .........................................................1
.............................................................1
........................................................2
....................................................3
..................................................3
.....................................................4
................................................5
...............................................................7
.............................................................8
...........................................................9
......................................................
13
.............................................................
10
.................................................
11
.......................................................
13
...............................................................
12
.....................................................6
................................................1
...............................................6
................................................
13
2.1 Product Specification
3.1 Appearance Design
3.2 Game Introduction
.............................................................
133.3 How to Play
2.2 Overview
2.3 Parts Name
2.4 Shipment List
2.5 Packing List
2.6 Instructions for installation
2.7 Warranty
1.2 Placing Site
1.3 Safety Precautions
1.4 Precaution during Play
1.5 Transporting and Moving
1.6 Installing and Placing
1.7 Caution & Warning Stickers
..............................................................
16
.....................
14
.........................................................
17
.............................................
17
..................................................
16
4. Test and Setting
3.3.1 Modification about game-machine top/prize slide-way
4.1 Test Mode
4.1.1.1 Prize Operation
4.1.1 Top Menu
..............................................
19
...............................................
20
....................................................
21
...................................................
24
........................................
24
............................................
26
............................................
26
.....................................
27
..............................................
27
.............................................
28
4.1.1.3 Game History
4.1.1.4 Error History
4.1.1.5 Setting
4.1.1.6 I/O Test
4.1.1.6.1 Pusher Unit Test
4.1.1.6.2 Shutter Test
4.1.1.6.3 Coin In Test
4.1.1.6.4 Switch&Sensor Test
4.1.1.6.5 Led Test
4.1.1.6.6 7Seg Test
............................................
284.1.1.6.7 Sound Test
.............................................
294.1.1.6.8 Aging Test
.....................................................
184.1.1.2 Meter

4.1.1.7 Data Clear ................................................. 30
4.1.1.8 Rom Version ...............................................
30
4.4 Sound List
4.5 Main-board DIP SW setting
4.2 Error Display
4.3 Error List
5. Maintenance and Service .........................................
39
5.1 Maintenance and service
5.2 Part Replacement
4.6 Displayed contents on the digital board at the time of coining
5.2.1 Change LED with casing
5.2.2 Replacement of ceiling lamp
5.2.3 Change door-frame acrylic soft-lamp-bar
5.2.4 Change prize-outlet soft-lamp-bar
5.2.5 Change control-panel soft-lamp-bar
5.2.6 Change control-panel joystick
5.2.7 Change control-panel button
............................................................
31
...............................................................
31
..............................................................
37
................................................
38
.....................
38
..................................................
39
........................................................
40
.............................................
40
..........................................
40
................................
41
......................................
42
....................................
42
.........................................
44
..........................................
45
5.2.10 Replacement of horizontally-moving sensors
5.2.11 Replacement of front/rear sensors
5.2.14 Replacement of colliding-sensors
5.2.13 Replacement of upper/lower limit sensors
5.2.12 Replacement of longitudinalyl-moving sensors
5.2.15 Replacement of sealing-plate opening/closing status sensors
5.2.16 Replacement of sealing-plate opening/closing position sensors
5.2.17 Replacement of optical-eye box
5.2.8 Change control-panel digital-board (7SEG)
5.2.9 Replacement of left/right sensors
..............................
45
......................................
46
...........................
46
....................................
47
..........................
47
..............................
47
.....................................
48
..............
48
............
48
......................................
49
...................................
49
............................
50
.............................
51
.............
52
.........................................
52
................................................
53
5.2.20 Replacement of horizontally-moving motor
5.2.19 Replacement of longitudinally-moving motor
5.2.18 Replacement of sealing-plate motor
5.2.21 Replacement of moving-up/down motor or polyurethane roller
5.2.22 Replacement of prize net
5.2.23 Replacement of top
5.2.24 Replacement of speaker
5.2.27 Replacement of fuse
5.2.26 Change leakage switch
5.2.25 Replacement of coin box
5.2.28 Change power-box
5.2.29 Replacement of PVC
5.2.30 Replacement of moving components
............................................
53
............................................
54
.............................................
54
...............................................
55
.................................................
55
...............................................
56
..................................
56
...................................
575.2.31 Replacement of sealing-door spring

5.2.32 Replacement of prize baffle.......................................... 58
5.2.33 Specification for height-adjusting net ..................................
58
5.2.34 Specification for the height of the ramp net .............................
59
5.2.35 Descriptions for damping-adjustable hinge .............................
60
5.2.36 Description for power socket.........................................
60
5.2.37 Description for LCD position and operation steps ........................
61
5.2.38 Descriptions for prize-rack...........................................
61
5.2.39 Descriptions for hole-cover of lower cover-plate .........................
62
6. Assembly........................................................
65
6.1 Assembly tree diagram
....................................................
65
6.2 Total components(PP-0000000) ............................................
66
6.3 Frame sub-components(PP-0100000) .......................................
67
6.3.1 Frame primary-components(PP-0101000) ..............................
68
6.3.2 Power-box components(PP-0102000) ..................................
69
6.3.3 Cashbox components(PP-0103000) ...................................
70
6.4 Control-panel components(PP-0200000) .....................................
84
6.5 Coin-door components(PP-0300000 )........................................
85
6.6 Large door-frame components(PP-0400000) ..................................
86
6.6.1 Door-frame acrylic components(PP-0401000 ) ...........................
87
6.6.2 Large acrylic-door components(PP-0402000 ) ...........................
88
6.7 General moving part components(PP-0500000) ...............................
89
6.7.1 Horizontally-moving front-rail components(PP-0501000) ...................
90
6.7.2 Horizontally-moving rear guide-rail components(PP-0502000) ..............
91
6.7.2.1 Horizontally-moving roller-plate components(PP-0502000-A) ...........
92
6.7.3 Longitudinally-moving rail components(PP-0503000)......................
93
6.7.3.1 Longitudinally-moving motor components(PP-0503000-A) .............
94
6.7.3.2 Longitudinally-moving frame components(PP-0503000-B) .............
95
6.3.6.1 PCB components(PP-0106000-A) .................................
74
6.3.7 Glass components on both sides(PP-0107000) ..........................
75
6.3.8 TILT components(PP-0108000) .......................................
76
6.3.9 Eyelet sensor components(PP-0109000) ...............................
77
6.3.9.1 Optical-eye box(PP-0109000-A) ...................................
78
6.3.10 Inner supporting-iron components(PP-0110000) ........................
79
6.3.11 Bottom sealing-plate components(PP-0111000) ........................
80
6.3.12 Prize sealing-plate door components(PP-0112000) ......................
81
6.3.13 Low-voltage power module(PP-0113000) ..............................
82
6.3.14 Door-closing motor components(PP-0114000) ..........................
83
6.3.6 PCB-box components(PP-0106000) ...................................
73
6.3.4 Prize-lane components(PP-0104000) ..................................
71
6.3.5 Prize-outlet mask components(PP-0105000) ............................
72
5.3 Replacement or repairing of main-board......................................
63

6.7.4 Horizontally-moving motor components(PP-0504000) .....................
96
6.7.5 Total jacking-rod components(PP-0505000) .............................
97
6.7.5.1 Jacking-rod fixing-wheel components(PP-0505000-A) .................
98
......................
99
6.7.5.2 Jacking-rod motor components(PP-0505000-B)
7. Printing Pattern
8. Wiring Diagram
After-Sales Service
.................................................
111
.................................................
110
6.8 Ramp net components(PP-0700000)
6.8.1 Net components(PP-0701000)
6.8.2 Prize ramp-panel components(PP-0702000)
6.8.3 Net movable-pin components(PP-0703000)
6.7.5.3 Jacking-rod sensor components(PP-0505000-C) ....................
100
6.7.5.4 Jacking-rod components(PP-0505000-D) ..........................
101
6.11 POP components(PP-1000000) ..........................................
109
..............................
108
.............................
107
.........................
105
...........................
106
............................
104
....................................
103
....................................
102
6.10 Prize display-board components(PP-0900000)
6.8.4 Net front-pillar components(PP-0704000)
6.9 Prize-lane cover-plate components(PP-0800000)

1.1 Warning Stickers
1.2 Placing Site
In order to avoid injury to related people and damage to property, please
observe the followings:
PLEASE READ FIRST
The following marks can be used to indicate the magnitudes of risk and
damage caused by ignorance or improper operation:
Warning
Warning
Caution
means “may result in serious injury or death”
means “may result in minor injury or property
damage”
Serious Injury: refers to the situations in which hospital treatment or long-term treatment
will be accepted because of losing sight, getting hurt, getting burnt, electric
shock, fracture or intoxication.
Minor Injury: refers to the cases that there is no need to go to hospital or accept long-term
treatment.
Property Damage: refers to the damage of house, facility, or hurt of livestock and pet
This machine is designed for indoor use only. Never install the machine
outdoors. Meanwhile, please avoid the following locations indoor：
please make sure the place line has been grounded before product
installation, setup, testing, operation or repair
The rear part has the vent for heat emission from PC or screen.
Don’t place anything nearby to avoid game failure.
Provide a space of minimum 30cm between the rear of the machine
and the wall for good ventilation and heat emission
1. Safety Precautions
Direct sunlight, water leakage, damp and high temperature places.
Near Flammable, volatile, or/and dangerous substance.
Slope, unstable places or locations subject to frequent vibration.
Near emergency exit, fire extinguisher or similar equipment.

Warning
1.3 Safety Precautions
The owner shall pay attention to the followings when placing, checking
and repairing machine to insure player’s security and avoid damage:
Make sure to plug the game into 110V or 220V main outlet to avoid fire
and electric shock.
please check the voltage is 110V or 220V before the machine connectes
to the power supply,or it may cause a fire or electric shock.
Do not unplug or plug the plug instantly.
Don’t touch the power plug with a wet hand to avoid electric shock.
Don’t expose the power cord/grounding line on the passageway.
Failure to do this will damage the power cord, causing electric shock
or short circuit.
Don’t lay anything near the power cord to avoid fire.
Do not pull the power cord when unplugging, please hold the plug to
avoid power cord damage, causing fire or electric shock.
Only use fuse and spare parts specified by our company
Connect the connector firmly and tighten the screws.
It is forbidden to push or pull the game-machine in order to prevent the
accidental danger.
Do not dismount, replace or convert the product without our permission
in order to avoid damage and human injury due to improper operation.
Check and maintain the machine regularly.
Keep “Warning stickers” clean and legible. Replace it immediately
when the words are not legible or the dirt can’t be removed.
Please contact our service center when performing any work that is
not described in this manual, and follow the instruction provided.
Make sure to turn off the power when performing maintenance and
service to avoid electric shock or short circuit.
In case of power cord damage, please contact the local distributor for
replacement

Transporting
When transporting the machine with an elevator, be sure to employ “Lift Point”
to prevent accident and damage to the machine.
To prevent movement when transporting the machine on a vehicle, please fix the
casters and fully retract the adjusters. Failure to do this may cause damage to the
machine.
When carrying the machine with a forklift, be sure to insert the fork to fork position
and lift stably. If not, it may cause accident and damage to the machine.
The Acrylic of the machine is fragile. High precision components are required for
vibration or shock resistance.
Moving
Before moving the machine, unplug the power plug to prevent accident.
Don’t damage the cord.
Pay attention to the obstructions and uneven surface when moving the machine
to prevent accident and damage to the machine.
Fully retract all adjusters before moving to prevent accident and hazard.
Make sure to use at least two persons to conduct the above work to avoid accident
and injury
Pay attention to the moving direction, see fig.
1.4 Precautions during Play
Caution
Caution
Person with poor health condition, such as hypertension or heart disease.
When a player feels uncomfortable during play, remind the person to have
a break, or stop playing.
Make sure the player reads the warning labels and other indications, and
plays in accordance with the instructions to avoid accidents such as electric
shock and short circuit.
Bystander shall not operate any button when the player is playing the game
to avoid unnecessary trouble.
It is forbidden to push or pull the game-machine in order to prevent the
accidental danger.
In order to avoid injury and accident during play, the following people shall
not play the game:
People who are injured or less mobile.
Person wearing high-heeled or slippery shoes.
Person who can’t touch the pedal.
Pregnant woman, drunk people.
1.5 Transporting and Moving

Use the adjusters to fix the machine (See diagram 1)
1.Loosen the nuts for the adjusters (clockwise), tighten the bolts with a wrench (clockwise).
2.Tighten the nut firmly(counter clockwise) and fix it well.
Diagram (1)
Diagram (2)
Provide a space of minimum 30cm between the rear of the machine and
the wall for good ventilation and heat emission (See diagram 2).
Wall
bracket
Lock nut
Lock place
Caster Adjuster Bolt
Caution
1.6 Installing and Placing
Pay attention to the following when placing the machine.
Place the machine on the flat and slip resistant area.

1.7 Caution & Warning Stickers
PPSG-P0010

6
2. Product Description
2.1 Product Specification
Side View
1220mm
582.6mm
Play area
443mm
168mm
Play area
457mm
1981mm
350mm
265mm
826mm 565mm
25mm
775mm
2566mm
795mm
700mm
Note：Adjustable height
of prize-rack
1220(W)×795(D)×2566(H)
Location Indoor Only
Dimension
220V
50Hz
160 W
210 kg
5~40。 C
265(W)×350(D)×300(H)
Max size of prize
560(W)×590(D)
Prize net size
Game-machine weight
Rated Voltage
Frequency
Power Consumption
Temperature Range
1 kg
Max weight of prize
Front View

7
Rear View
Bottom View
Side View
Top View
2.2 Overview

Side-door
AC-BOX
Rear door plank
POP components
Hardware frame
Coin-acceptor
Control-panel
components
Net
components
Displaying-board
components
Prize-outlet mask
components
Large door-frame
acrylic components
Large transparent-door
components
Moving-part
components
Prize outlet-door
Speaker
8
2.3 Parts Name

9
1
1
2
1
3
1
9
1
8
1
10
10
7
1
6
1
4
15 1
Note：Fix to the top of the game-machine
with bubble film & plastic wrap.
Note：1. Wrap it with plastic wrap.
2. Fix to the screen with cable ties.
Note：Fix to the
front door with
plastic wrap.
10 PP-0900A04 Prize-frame tube 6061 10
9 PP-1000000 POP components 1
8 PP-0701A10 Large prize net 1
7 PP-0000000 Total components 1
6 Accessory box 1
5 PP-9901E05 No.2 frame limit-bar Solid wood 20*40*1260 1
4 PP-9901E04 No.1 frame limit-bar Solid wood 20*30*700 1
3 PP-9901E03 Frame cover Water resistance 2C 850g T-7 1
2 PP-9901E02 Frame enclosure Water resistance 2C 850g T-7 1
1 PP-9901E01 Frame platform 1
2.4 Shipment List
Modes of packing
SN Name QtyDrawing No. Materials/specifications Note
条形码粘贴处

Power cord
(two-end three-pin)
Large top
Lock of same size
B17 key B17 key,No.6687
5052-O
5052-O
3m（1.0mm ) 250V 1
2
1
1
2.5 Packing List
Please check the following items after purchasing our product. If any part
missing or damaged, please contact our sales person!
Description Specification Quantity Remarks
Straight top
Fuse tube
Art paper
218 series
T3.15A/5×20
250V
1
1
Instructions
PC-3.0T 3
Long prize baffle
1
Large prize net
10
Diameter：25mmDiameter：25mm
Diameter：14mmDiameter：14mm
50mm50mm
50mm
50mm

11
Remove POP components and screw
it onto the top of the game-machine.
Before the game-machine is powered on, cut off the cable ties at this
position (for fixing X/Y axes of moving parts during transportation).
On the contrary, when the game-machine is moved, the position
must be tightened with the cable ties!
Warning
Note：X/Y axes of moving
parts are provided with 2
cable ties respectively!
2.6 Instructions for installation
Fix POP components to the top of the game-machine with 5 screws.

12
2.7 Warranty
Damage caused by force majeure such as god will.
Failure caused by carelessness, such as water contact, falling down,
toppling, knocking.
Failure caused by disobeying the instructions in this manual.
Failure caused by operating the machine on inappropriate site.
Change the original design and configuration for the game without notice.
Failure to perform regular service and clean.
Failure to fix the product in line with the manual’s requirement.
Malfunction or part damage caused by electromagnetic interference other
electronic equipments generated.
Non-warranty Consumables
Light tube and bulb
Button lamp and switch
Fragile items
Solenoid
Other spare parts
Scope
Inquiry regarding product can be assisted for free.
The warranty scope for consumables and durables may differ from product
to product. Please contact our after-sales service center for detailed
information. The right of final interpretation is reserved.
Exclusive

13
3.2 Game introduction
The color of "PUSHING POINTS" is mainly white and the game-machine is designed
very simply and elegantly. After it is powered on, its lamp is bright and dazzling. The
game-machine can display different styles by replacing 3 pieces of PVC. In the gaming
area, there are 5 layers of prize-racks. The positions of the prize-racks can be adjusted
according to the sizes of the prizes. The different sizes of prizes can be placed on the
grid. The player can get the prizes on the grid by challenging!
"PUSHING POINTS" is a single-player game that tests the player's reflexes. After the
coins are put in, the player can use the joystick to control the left/right movement of the
jacking-rod to determine its position within 30s and then press the button to jack the
prize. If the prize is not jacked, the player will not get the prize. If the prize is jacked, the
player will get the prize!
3.3 How to play
1. Put in the coins. 2. Select the prize and control the left/right
movement of the jacking-rod by using the
joystick.
4. Press the button and jack the prize by
use of the jacking-rod .
3. Then use the joystick to control the
left/right movement of the jacking-rod to
aim at the target.
3. Game Description
3.1 Appearance Design

14
6. The player can get the prize at the prize
outlet!
1
2
3
Its top is provided with
7 fixable positions.
3.3.1 Modification about game-machine top/prize slide-way3.3.1 Modification about game-machine top/prize slide-way
Its top is provided with screws and nuts that can be modified into various operating methods.Its top is provided with screws and nuts that can be modified into various operating methods.
Its top is provided with 7 fixable positions.Its top is provided with 7 fixable positions.
Use the rope to fix the pipe, as shown in the picture. The prize can be hung onto
the round-pipe ( Ancillary modified-parts to the game-machine)
Use the rope to fix the pipe, as shown in the picture. The prize can be hung onto
the round-pipe ( Ancillary modified-parts to the game-machine)
5. When the prize is jacked by the jack-
ing-rod, the player can get the prize
successfully!