Walker Edison BDOL User manual

Instruction Manual
IMPORTANT INFORMATION
READ BEFORE ASSEMBLING THIS PRODUCT
Follow the information on the warning labels found on the bunk bed and on the packaging.
Do not remove the warning label from the bed.
Use only a mattress with the dimensions 74-75 in.L x 51.5-52.5 in.W x 9 in.H on the upper
bunk.
The surface of the mattress must be at least 5 in. (127mm) below the upper edge of the
guardrails. Mattress must not exceed the maximum thickness of 9 in.
Always use the recommended size of mattress or mattress support, or both, to help prevent
the likelihood of entrapment or falls.
The use of a water or sleep flotation mattress is prohibited.
Replacement parts, including additional guardrails, may be obtained from any of Walker
Edison Furniture Company’s dealers or by contacting us online at www.walkeredison.com.
DO NOT use substitute parts. Contact the manufacturer or dealer for replacement parts.
Always use guardrails on the upper bunk. If the bunk bed will by placed next to a wall, the
guardrail running the full length of the bed should by placed against the wall to prevent
entrapment between the bed and the wall.
Periodically check that the guardrails, ladders and other components of the bed are in their
proper position, free from damage, and that all connectors are tight.
Always use the ladder to access the upper bunk.
DO NOT allow children under 6 years of age to use the upper bunk.
DO NOT allow horseplay on or under the bed. Prohibit jumping on the bed.
Prohibit more than one person on the upper bunk.
The use of a night light may provide an added safety precaution for a child using the upper
bunk.
STRANGULATION HAZARD – Never attach or hang items to any part of the bunk bed that
are not designed for use with the bed; including but not limited to hooks, belts and jump
ropes.
Keep these instructions for future reference.

Attach post (1) to the left side of ladder rungs (7) using double-ended screws (D) and rounded
washers (K). Attach ladder rail (6) to the right side of ladder rungs (7) using medium bolts (A)
and rounded washers (K). Tighten medium bolts (A) with small wrench (M).
Attach guardrail (5) and crossbar (8) to post (1) using small bolts (C) and small washers (F) .
Attach post (3) to guardrail (5) and crossbar (8) using small bolts (C) and small washers (F).
Tighten small bolts (C) with small wrench (M).

Secure ladder rail (6) to guardrail (5) using samll bolt (C) and samll washer F). Secure ladder
rail (6) to crossbar (8) using large bolt (B) and large washer (E) .Tighten samll washer (F) with
samll wrench (M) and large bolt (B) with large wrench (L).
Attach post (2) to the right side of ladder rungs (7) using double-ended screws (D) and rounded
washers (K). Attach ladder rail (6) to the left side of ladder rungs (7) using medium bolts (A)
and rounded washers (K). Tighten medium bolts (A) with small wrench (M).

Attach guardrail (5) and crossbar (8) to post (2) using small bolts (C) and small washers (F) .
Attach post (4) to guardrail (5) and crossbar (8) using small bolts (C) and small washers (F).
Tighten small bolts (C) with small wrench (M).
Secure ladder rail (6) to guardrail (5) using samll bolt (C) and samll washer F). Secure ladder
rail (6) to crossbar (8) using large bolt (B) and large washer (E) .Tighten samll washer (F) with
samll wrench (M) and large bolt (B) with large wrench (L).

Attach crossbars (10,11,12,14) to the assembly from Step 3 using small bolts (C) and small
washers (F) .Tighten samll bolts (C) with samll wrench (M).

Attach crossbars (10,11,12,14) to the assembly from Step 6 using small bolts (C) and small
washers (F) .Tighten samll bolts (C) with samll wrench (M).

Insert mattress support bars (9) into the provoded slots of crossbars (10,11).Secure mattress
support bars (9) by snapping plastic tab locks (I) into the provided slots of crossbars (10,11).
Note that it may be necessary to apply more pressure to some plastic tab locks than others.

Snap plastic links (J) onto the middle of mattress support bars (9).Attach angle bracket (N) to
crossbar (14) using small bolts (C) and small washers (F) .Tighten samll bolts (C) with samll
wrench (M).
M
14

Attach guardrails (13) to posts (1,2,3,4) using small bolts (C) and small washers (F) .
Tighten small bolts (C) with samll wrench (M).

Secure front guardrail (13) to crossbar (10) using large bolts (B) and large washers (E). Secure
back guardrail (13) to crossbar (11) using large bolts (B), large washers (E) and, where applicable,
angle brackets (G).* Tighten large bolts (B) with large wrench (L).
*OPTIONAL: Angle brackets (G) can be used to attach the bed to a wall for additional support. You must use hardware
suitable for the particular wall type, which is not included as there are many different wall types. You must also mount the
bed to the structure of the wall (i.e. wood studs, metal studs or cement/brick) directly. DO NOT attach the bed to the
surface of the wall without anchoring into the structural framework of the wall. Please seek professional advice if you are
unsure of your own ability to do this correctly. Walker Edison Furniture Company makes no representation of warranty,
expressed or implied, to the strength of any structure and the wall’s ability to hold your bed. You assume all responsibility
and indemnify Walker Edison Furniture Company of any and all damages that may be incurred by attaching your bed to
the wall.
10

Screw small bolts (C) and insert plastic plugs (H) into the bunk bed assembly.This will fill the
holes that are used only with the optional accessory attachments,which are sold separately.