Walker Edison WQ52C4DR User manual

ITEM # : WQ52C4DR
Assembly Instructions
  
 
Revised 03/2017
Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reseed. P.1

Screw cam bolts (B) into top panel (1). Attach door stoppers (D,E) to top panel (1) usng
medium screw (F).
Attach legs (14) to bottom panel (2) using large bolts (G) and wrench (V). Insert dowels (A)
into slats (11,12,13). Screw cam bolts (B) into slat (11

Screw cam bolts (B) into doors (15,16). Attach handles (H) to doors (15,16,17,18) using small
bolts (I). Attach door stopper plates (J) to doors (15,16,17,18) using small screws (K). Attach
door hinge (R) to door (17) and door hinge (Q) to door (18) using small screws (K).
Screw cam bolts (B) into panels (3,4,5,6). Insert dowels (A) into panels (3,4,5,6) and
shelves (8).

Screw cam bolts (B) into panels (19,20,21,22). Insert dowels (A) into shelves (23,24) and
panels (19,20,21,22).
Insert cam locks (C) into panel (8). Attach panels (3,5) to panel (8) using cam bolts and
dowels as guides. Tighten cam locks (C) with a screwdriver.

Insert cam locks (C) into panel (8). Attach panels (4,6) to panel (8) using cam bolts and
dowels as guides. Tighten cam locks (C) with a screwdriver.
Attach the assemblies from Step 6 and Step 7 to bottom panel (2) using large bolts (G)
and wrench (V).

Attach slats (12,13) to slat (11) using cam bolts as guides. Insert cam locks (C) into
slats (12,13) and tighten with a screwdriver.
Attach the slat assembly from Step 9 to bottom panel (2) by inserting the dowels of the slat
assembly into the pre-drilled holes of bottom panel (2).

Slide back panels (9,10) into the stand assembly. Note that the back panels will slide down
in the grooves along the back of the stand assembly.
Insert cam locks (C) into the stand assembly. Attach top panel (1) to the stand assembly
using cam bolts and dowels as guides. Tighten cam locks (C) with a screwdriver.

Insert plastic pivots (L) into top panel (1) and bottom panel (2).
Insert door hinge (Q) into bottom left plastic pivot (L). Slide door (17) into place by inserting pre-attached door
hinge (R) into top left plastic pivot (L). Attach door hinge (Q) to door (17) using small screws (K). Insert door
hinge (R) into bottom right plastic pivot (L). Slide door (18) into place by inserting pre-attached door hinge (Q)
into top right plastic pivot (L). Attach door hinge (R) to door (18) using small screws (K).

Attach panels (19,20) to shelves (23,24) using cam bolts and dowels as guides. Insert cam
locks (C) into shelves (23,24) and tighten with a screwdriver. Note that two cam locks will be
inserted into each shelf.
Attach panels (21,22) to shelves (23,24) using cam bolts and dowels as guides. Insert cam
locks (C) into shelves (23,24) and tighten with a screwdriver. Note that two cam locks will be
inserted into each shelf.

Attach the shelf assembly from Step 15 to door (15) using cam bolts and dowels as guides.
Insert cam locks (C) into panels (19,20) and tighten with a screwdriver. Note that two cam
locks will be inserted into each panel.
Attach the shelf assembly from Step 16 to door (16) using cam bolts and dowels as guides.
Insert cam locks (C) into panels (21,22) and tighten with a screwdriver. Note that two cam
locks will be inserted into each panel

Attach door hinges (M) to panels (3,4) using large screws (N) and small screws (P).
Attach door assembly (19,20) to the stand assembly at door hinges (M) using large
screws (N).

Attach door assembly (21,22) to the opposite side of the stand assembly at door hinges (M)
using large screws (N).
Insert shelf support pins (S) into the stand assembly at desired shelf heights. Carefully place
shelves (7) onto shelf support pins (S).

Secure back panels (9,10) using plastic wedges (T) and large screws (U).