Walker Edison BR1DNS User manual

BR1DNS
Assembly Instructions
P.1
Keep these instructions for future reference.
Revised 01/2018
All manuals and user guides at all-guides.com

P.2
All manuals and user guides at all-guides.com

P.3
1
7
2
3
4
5
6
8
9
10
11
12
13
14
8
9
15
Right side panel
Top panel
Back panel
Upper front crossbeam
Left side panel
Bottom front crossbeam
1
2
3
4
5
6
7
01 pcs
Right foot
Left foot
Front drawer
Left side drawer
8
9
10
11
02 pcs
02 pcs
Drawer bottom
Right side drawer
12
13
Drawer back
14
Back crossbeam
Base
15
01 pcs
01 pcs
01 pcs
01 pcs
01 pcs
01 pcs
01 pcs
01 pcs
01 pcs
01 pcs
01 pcs
01 pcs
All manuals and user guides at all-guides.com

P.4
A
B
C
D
E
F
G
H
I
J
K
Ø8*30mm Wooden dowel 26 pcs
Ø3,0*14mm Screw
Glue
06 pcs
Ø6,0*10mm Screw 04 pcs
Ø4,0*30mm Screw 27 pcs
M4*22mm Screw 01 pcs
Ø4,5*45mm Screw 12 pcs
Ø10*10 Nail 16 pcs
300mm Right Slide 01 pcs
300mm Left Slide 01 pcs
Knob 01 pcs
01 pcs
Hammer
recommended for assembly
(not included)
All manuals and user guides at all-guides.com

P.5
Step 1
Step 2
Please assemble on
a clean soft surface
to avoid damage.
2
6
4
5
12
A
11
3
A
C
C
C
C
Please assemble on
a clean soft surface
to avoid damage.
IH
Pre-Drilled holes
3
The wheel to
the Front
The wheel to
the Front
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
15
C
I
C
H
2
A
Ø8*30mm
26
C
H
Ø6,0*10mm
04
Right slide 300mm
01
I
Left slide 300mm
01
K
Glue tube
01
All manuals and user guides at all-guides.com

P.6
Step 3
Step 4
D
3
D
D
15
D
DD
D
D
DD
D
2
6
4
5
D
Ø4,0*30mm
03
D
Ø4,0*30mm
07
K
Glue tube
01
K
Glue tube
01
All manuals and user guides at all-guides.com

P.7
Step 5
Step 6
1
D
D
D
D
D
D
DD
D
Ø4,0*30mm
06
D
Ø4,0*30mm
03
K
Glue tube
01
All manuals and user guides at all-guides.com

P.8
Step 7
Step 8
9
8
F
F
F
F
F
F
F
F
8
9
G
7
G
G
G
G
G
G
G
G
G
G
G
G
G
F
Ø4,5*45mm
12
G
Ø10*10
16
F
F
F
K
K
Glue tube
01
1º 2º
Apply glue to leg
contact surfaces
All manuals and user guides at all-guides.com

P.9
Step 9
Step 10
DD
D
D
B
B
B
B
E
J
I
H
B
B
10
12
11
13
14
The wheel to
the Back
Bottom
DD
DD
E
H
M4x22mm 01
Right slide 300mm
01
I
J
Left slide 300mm
01
01
B
D
Ø3,0*14mm 04
Ø4,0*30mm 08
All manuals and user guides at all-guides.com

Step 11
To adjust the drawer front position:
Loosen the screw (part C) you used to
install the drawer runner (either parts H
or I) in step 2, to the side panel
(parts 02 or 03), depending on the side
(left or right), as shown.
With the screw (part C) loosened, you
can make the necessary slight
adjustments (up or down) to the drawer
runner to achieve the proper drawer
alignment.
Once the drawer alignment is square, secure
the position of the drawer runners (parts H &
I) to the side panels (parts 02 & 03) by re-
tightening the part C screw and adding the
part B screw as shown.
BØ3,0*14mm 02
P.10
C
C
B
All manuals and user guides at all-guides.com