Walker Edison TNNB4C User manual

Assembly Instructions
Copyright © 2018, by Walker Edison Furniture Co., LLC, All rights reserved.
Please visit our website for the most current instructions, assembly tips, to report damage
or request parts. www.walkeredison.com
Revised 10/2022
P.1
TNNB4C

I. Ensure that all parts and hardware are available before beginning assembly.
II. Follow each step carefully to ensure the proper assembly of this product.
III. Two people are recommended for ease in the assembly of this product.
IV. The three main types of hardware used to assemble this product are wood
dowels, screws and bolts.
V. The provided glue is to secure wood dowels in place. When first inserting dowels, locate
the appropriate hole for the dowel, place a small amount of glue in the hole and insert
the dowel. Wipe away excess glue immediately.
In future assembly steps when dowels are necessary to attach assembly parts together,
place a small amount of glue on the end of the dowel before attaching parts together.
Wipe away excess glue immediately.
VI. A Phillips head screwdriver and hammer is required for the assembly of this product.
VII. Power tools should not be used to assemble this product.
VIII. Maintenance Guide
To maintain long term performance and easy gliding of your solid wood drawers, we recommend
applying wax to the wooden guide rails.
1. Bee's wax is recommended or Paraffin wax from a standard candle can be used.
2. Apply the wax by rubbing it on the wooden guide rails where there is wood-on-wood contact
when opening and closing the drawer. (Wax should be room temperature, do not melt the wax
onto the wood)
3. Wax should be applied every few months for the first year and then only when needed after
that to keep the drawers sliding smoothly.
General Assembly Guidelines
P.2

9
Top panel
10 pc1
Left side panel
201 pc
Right side panel
23 01 pc
24 0 pc1
5Drawer front 01 pc Drawer runner
Description Qty
Part# Description Qty
Part#
Drawer bottom
13 0 pcs2
14 0 pc1
01 pc
60 pc1
Parts List
Base panel
Front crossbeam
Drawer back
80 pcs2
Bottom crossbeam
10 0 pc1
Back Panel
11 01 pc
Drawer Left Side
12 0 pc1
Drawer SideRight
P.3
7
90 pcs4
Leg
5
12
14
11
7
1
23
2
6
8
8
9
9
13
13
10
24
9

Philips head screwdriver required for assembly
(not included)
Hammer recommended for assembly
(not included)
Hardware List
The hardware quantities listed above are required for proper assembly.
Some extra hardware may also have been included.
A
B
E
F
G
H
J
K
Ø8*20mm Wood dowel 04 pcs
Ø8*30mm Wood dowel 30 pcs
Ø4,0*25mm Screw 04 pcs
Cam bolt 14 pcs
Cam lock 14 pcs
Ø8*8mm Nail 16 pcs
Ø4,0*30mm Screw 12 pcs
Ø4,0*40mm Screw 04 pcs
I- Glue 01 pc
DØ3,5*35mm Screw 08 pcs
C-08 pcs
Slap hole
P.4
Ø7,0*33mm
Ø15*12mm

Insert wood dowel (B) and glue ( ) intoI
part (2), (6), (8), (11), (12), (23) and (24).
Insert ood dowelw
A and glue ( ) 13( ) into part ( ).I
Step 3
Please assemble on
a clean soft surface
to avoid damage.
Screw cam bolts (H) into parts (1), (23) and (24) with a screwdriver.
P.5
A
13
2x A
Step 2
A
B
H
H
H
H
H
H
H
HH
B26
Ø8*30mm
I01
B
B
B
B
2
2x
B
B
B
B
8
B
B
6
BB
12
B
B
11
H
H
H
H
H
H
1
H14
B
B
23
B
B
24
23
24
Step 1
A04
Ø8*20mm
I01
Attention to the
dowel size:
Ø8*20mm
A

J
E
Step 5
Step 4
E04
Ø4,0*25mm
J04
P.6
13
Secure part ( ) to part ( ) and ( ) with screw ( ) and screwdriver.s 13 23 24 E
Secure parts (2) and (6) to part (24). Insert cam locks (J)
into part (2) (6), and tighten with a screwdriver.
J
J
J
TOP
TOP
beveled
side!
E
E
13
23
24
24
unpainted!
E
13
E
2
6
J
1st
2nd
3nd

Step 6
Step 7
P.7
J04
J06
1
Secure part (23) to parts (2) and (6). Insert cam locks (J)
into part (2) (6), and tighten with a screwdriver.
J
J
J
2
Secure part (1) to parts (23) and (34). Insert cam locks (J)
into part (23) and (24). Tighten with a screwdriver.
J
JJ
J
J
J
6
J
23
24
23
J
1st
2nd
3nd
J
1st
2nd
3nd

9
Step 8
Step 9
P.8
Secure parts (8) to part (2) with wood dowels.
2
Secure parts (9) x2 to part (23) and parts (8) x2 with screw
(D) using the predrilled holes through (23) into parts (9).
Secure parts (9) x2 to part (24) and parts (8) x2 with screw (D)
using the predrilled holes through (24) into parts (9) D08
Ø3,5*35mm
9
D
9
3
D
D
D
D
8
D
8
8
23
24
8
8
9
9

Step 10
P.9
F04
Ø4,0*30mm
Secure part (8) to part (9) with screw (F) and screwdriver.
F
Step 11
9
9
9
9
8
8
F
F
F
F
G04
Ø4,0*40mm
Secure part (8) to part (2) with screw (G) and screwdriver.
G
8
8
2
G
G
G
G

K
Name and address of
the supplier and date of
production.
K
K
K
K
K
K
K
K
K
Ø * mm8 8
K16
10
Step 12
P.10
Secure back panel (1 ) to body with nails ( ) nd hammer.0 K a
K
B
B
Insert ood dowel ( ) into part ( ) to be the stop of the drawer.w B 13
13
B02
Ø8*30mm
Step 13
13
B
K
K
K
K
K
K