Walker Edison BWJRTOL User manual

Révisé en 12/2017
2018
Revised 02/2023 V-3
P.1
Item #: BWJRTOL
Assembly Instructions
Triple Bunk Bed
Assembly Instructions
TO ASSEMBLE THE
TRIPLE BUNK BED ITEM,
YOU ALSO NEED THE BWJRTOT
BUNK BED

DANGER D’ ÉTRANGLEMENT- Ne jamais attacher ni suspendre quelque chose au lit, qui
ne fait pas partie du lit superposé. Ceci inclut, sans s’y limiter : crochets, ceintures ou cordes
à sauter.
P.2
H on the upper
7
74-75 in. L x 37 1/2 - 38 1/2 in. W x 7 in.
WALKER EDIS ON

P.3
23
18 18
31
17
17
30
06
13
08
09
06
22
15
15
05
05
14
13
10
10
13

P.4
Ref.
A
F
O
P
03
26
08
G
H
I
J
L
08
08
12
02
01
32
1/4x90mm
1/4
4,0x30mm
10x40mm
7x80mm
7x120mm
7x100mm
7x40mm
Hex Key
Qty.

Step 1
Step 2
P.5
A10
10x40mm
Insert wood dowels (A) into slats (10,13,14 and 15).
Insert wood dowels (A) into guard rails (17,18)
and side rails (30, 31).
A
AA
A
A
AA
AAAAA
AA
A
AAA
AA
A
A
A
A
A
A
1413 10
1313 10
1515
A16
10x40mm
18
17
18
17
31
30

Step 3
Step 4
P.6
H
H
L
L
06
06
01
01
7x120mm
7x120mm
Hex Key
Hex Key
Attach legs (6 and 8) to slats (10,13,14) using
screws (H) and Hex Key (L).
Attach legs (6 and 9) to slats (10 and 13)
using screws (H) and Hex Key (L).
14
13
10 06
08
13
13
10
06
09
H
H
H
H
H
H
H
H
H
H
H
H
L
L

Step 5
Step 6
P.7
1/4
1/4
O
O
P
L
L
P
L
L
04
04
01
01
04
04
01
01
1/4x90mm
1/4x90mm
Hex Key
Hex Key
Hex Key
Hex Key
O
O
O
O
O
O
O
O
O
O
O
O
P
P
L
L
L
L
31
6
9
6
8
30
P
P
P
P
P
P
P
P
O
O
O
O
O
O
L
Insert half moon nut (P) into side rail (31), Attach side rail (31)
to legs (6 and 9) using bolts (O) and Hex Key (L)
Leave the bolts (O) loose for future Steps
Insert half moon nut (P) into side rail (30), Attach side rail (30)
to legs (6 and 8) using bolts (O) and Hex Key (L)
Leave the bolts (O) loose for future Steps

P.8
Step 7
Step 8
G
G
G
G
L
L
18 18
15
15
G
GL
G
G
L
L
L
L
04
02
01
01
01
01
7x80mm
7x80mm
Hex Key
Hex Key
Hex Key
Hex Key
Attach guard rails (18) to legs (6 and 9) using bolts (G)
and Hex Key (L).
Then tighten (D) on Side Rails (30, 31).
Attach part (15) to leg (8) using bolts (G)
and Hex Key (L).
6
31
30
9
8

P.9
Step 9
Step 10
I
I
I
I
I
I
FF
F
F
L
L
I
L
L
L
L
02
01
01
01
01
7x100mm
Hex Key
Hex Key
Hex Key
Hex Key
L
L
G
G
L
Attach ladder side rail (22) to part (15)
and side rail (30) using bolts (I and F)
and Hex Key (L).
Attach guard rail (17) to leg (06) and ladder side rail (22)
using bolts (G and F) and Hex Key (L).
22
17 17
22
6
15
15
30
15
30
22
F
F
01
02
7x40mm
7x40mm
G02
7x80mm

P.10
J06
4,0x30
05
J
J
J
J
J
J
36 3/8"
29 1/2"
Connect guard rail support (05) to guard rail (17,18)
and bed rail (30 and 31) using screw (J).
Follow measurements shown in diagram.
Step 11
05
18 18 31
17
17
30

Step 12
2 1/2"
23
P.11
J26
4,0x30mm
Install slat kit (23) to bed rails with screws (J). Spacer tape will face up.
J
JJ
J
J
J
J
J
J
J
J
JJ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
31
30
30
31
Apply pressure to cross
beams (30,31) to ensure
that mattress supports
(23) fit evenly between
cross beams
Fix the slats as shown
in the drawing, on the
support of the rails to
avoid accidents
!

P.12