WarmlyYours TWS1-HRN08 User manual

TOOLS REQUIRED ACCESSORIES FOR SQUARE/ROUND MOUNTING TUBES
INSTRUCTIONS
Before using this product, please read the following instructions carefully and keep this
pamphlet for future reference.
ABOUT THE PRODUCT:
This heated towel warmer is designed for drying/warming towels or clothes, it has a surface
stabilized temperature of 122-131ºF, and it is used in household bathrooms and kitchens, as
well as in hotels and restaurants or other public areas. This appliance uses a voltage of 120
VAC, and is manufactured according to cULus standards.
SAFETY PRECAUTIONS:
1. The towel warmer must be used with a Ground Fault Circuit Intercepter (GFCI) circuit.
2. This product is supplied with a three-prong plug or three-wire cable.
To avoid unnecessary risk or danger, this product must be properly grounded.
3. Any repairs must be done by a qualified technician who is deemed qualified by industry
standards. When any external wire fittings are required, the unit must be disconnected
from the circuit.
WARNING:
1. Only use for drying textiles which have been dampened by water.
2. If heating wire is damaged, the whole product should be replaced.
NOTE:
1. In the event of any difference in technical specifications, please refer to the actual product.
2. Please wipe the towel rail with a soft, dry cloth when cleaning it.
Do not use scrubbers or abrasive cleaners.
Installation Support •[phone] • WarmlyYours
Installation Fittings:
(1+2): Mounting tubes (2 pieces) & Set screws (4 pieces)
(3) 3 brackets (2 large, 1 small)
(4) Short mounting screws (3 pieces) Long mounting screw (1 piece)
(5) Drywall anchor (3 pieces)
(6) Long screws (3 pieces)
(7) Mounting Shelf (1 piece)
(8) Power-source faceplate with mounting bracket (1 piece)
This product must be installed in accordance with the instructions in
the manual and the NEC and CEC guidelines relating to electrical
fixtures in bathrooms. The Towel Warmer must be on a GFCI
protected circuit and be wired by a professional who is certified
to do electrical wiring.
In order to reduce electrical shock, this towel warmer should be
installed on a 15A GFCI protected branch circuit (14AWG) and to an
outlet box that is 4 inches (10.16 cm) high by 2 Inches
(5.08 cm) wide.
1+2
35
7
8
46
INSTALLATION GUIDE
For TWS1-HRN08 hardwired towel warmers

Installation Support •[phone] • WarmlyYours
ACCESSORIES
1 PCS
4 PCS
3 PCS
4 PCS
3 PCS
1 PCS
3 PCS
1 PCS
2 PCS
a
c
d
e
i
j
k
f
g
h
INSTALLATION: (WARNING: The electrical
connection should avoid all water.)
Please refer to all the following steps if the wall
brackets are taken apart from the vertical bars.
Please refer to Steps 5-10 if the wall brackets are
fixed on vertical bars already.
1 PCS
b
INSTALLATION GUIDE
For TWS1-HRN08 hardwired towel warmers
STEP 1 STEP 1:Remove and set aside the set screws (c)
from the top of the main assembly.
STEP 2:Slide the mounting shelf's collared feet (k) over the
top of the main assembly so that the mounting shelf is
perpendicular to the main assembly.
Note: the hole's in the mounting shelf should face the same
direction as the wiring from the back of the main assembly.
STEP 3:Secure the mounting shelf (k) fto the main
assembly by using the set screws (c) from Step 1.
STEP 4:Insert the short mounting screw (d)
through the tube in the center of the mount-
ing tube (a).
c
STEP 2
k
STEP 3
k
c
STEP 4

STEP 8:Insert long screw (h) through
mounting bracket (g), then screw into plastic
drywall anchor (f).
Note: the two larger brackets are designed to be
used to secure the mounting shelf. The smallest
bracket should be used to secure one of the
mounting tubes, while the other is secured by the
power-source faceplate with mounting bracket.
STEP 8
STEP 9:Install the tube (a and b) onto the
bracket (g).
STEP 9
STEP 10:As shown in the picture, install the
set screws (c) into the hole of all the tubes (a,b
and k) using the allen wrench; fix the tube (a,b
and k) onto the mounting bracket (g).
STEP 10
Installation Support •[phone] • WarmlyYours
INSTALLATION GUIDE
For TWS1-HRN08 hardwired towel warmers
STEP 5:Use a tape measure to measure the distance
between the center points of each wall bracket tube;
record the distances between points AB, AC, CD, and
BD. Mounting point C will determine electrical box
location. See Electrical Assembly in following
instructions.
STEP 5
STEP 6:Mark A, B, C, and D according to the data from
Step 5; It is suggested that this product be installed at
least 23.5 inches (59.69 cm) above floor level.
(WARNING: The electrical connection should avoid all
water). This mounting location must comply with all local
building and electrical codes.
Place towel warmer on the box (or a large sheet of paper)
and lay on a flat surface with mounting tubes facing
downwards. Mark the location of the following:
• The electrical collar (hardwired model only)
• The location of the mounting tubes
Use the template as a guide to mark the wall with the correct
locations of the four mounting tubes (A, B, C, and D)
STEP 6
STEP 7:Drill A, B, C, and D holes with an
appropriately sized bit. Use a hammer to knock
plastic drywall anchor (f) into wall completely.
STEP 7
ALTERNATIVE TO STEPS 5 & 6
AB
D
C
A
D
C
B

Junction
box for
optional
control.
2” x 4” ELECTRICAL BOX
HOT LOAD
(black or blue)
Non-Heated
Mounting Shelf
GROUND
(green/yellow)
NEUTRAL LOAD
(white or brown)
CAUTION：
To provide continued protection against risk of electric shock,
connect to properly grounded outlets only.
Grounding wire
fixed to the
junction box
cover plate by
ground screw.
Installation Support •[phone] • WarmlyYours
ELECTRICAL ASSEMBLY
INSTALLATION GUIDE
For TWS1-HRN08 hardwired towel warmers
SWITCH
(j)
(i)
(b)
(c)