Warner RF FMT5.0-50 User manual

FMT5.0 instruction manual
Initial preparation work:
First set up the antenna cable and connect it to the transmitter's RFOUT
port, then plug the power cord into the transmitter's power outlet. Next,
insert the audio cable to the XLR header or RCA outlet, the outlet is
divided into two channels. Connection is complete, please turn on the
transmitter panel POWER button, the device starts.
Transmitter boot interface
Model / equipment name / manufacturer information

The transmitter starts default configuration
Transmitter boot. The progress bar enters the selected setting in about 10 seconds. Turn
the knob to select, short press the knob to confirm.
Last config Last configuration, the latest shutdown configuration.
Default config default configuration, the system default frequency 98MHZ / power OW /
stereo + external modulation / audio pre-emphasis 0 / volume gain 0dB.
PLL lock wait
Waiting time about 2-10 seconds.
Main interface
F: Current frequency POW: Current power VSWR: Standing wave ratio L Left channel level
DRIVE: Amplifier Push TEMP: Amplifier Temperature MOD Modulation Level R Right channel
level
Short press the knob to enter the menu settings, turn the knob to select the desired setting
menu.
Menu 1 frequency setting
Short press the knob to enter the frequency setting.

Current frequency: current frequency
Frequency setting: Set the frequency
Turn the knob to adjust the frequency setting, short press the knob to confirm the frequency
setting.
The PLL locks again for each frequency setting. After the lock is completed, return to menu 1
frequency setting.
Menu 2 power settings
Short press the knob to enter the power setting.
Current RF power: Current RF power Drive: Amplifier push
RF power setting: RF power setting VSWR: VSWR
Turn the knob to adjust the power setting, press the knob to confirm the power setting. And
return to menu 2 power settings.
Menu 3 signal modulation settings

Short press the knob to enter the signal modulation setting.
Current signal mode: Current signal mode
Signal mode setting: Signal mode setting
STEREO + EXT MOD Stereo + External Modulation Input
MONO + EXT MOD Mono + External Modulation Input
EXT MOD External Modulation Input
STEREO Stereo Input
Turn the knob to adjust the signal mode setting, short press the knob to confirm the signal
mode setting. And return to menu 3 signal mode setting.
Menu 4 audio pre-emphasis settings
Short press the knob to enter the short press knob to enter the signal modulation setting.

Current pre-emphasis: The current pre-emphasis
Pre-emphasis setting: Pre-emphasis setting
Turn the knob to adjust the audio pre-emphasis setting, short press the knob to
confirm the audio pre-emphasis setting. And return to menu 4 Audio Pre-emphasis
Settings.
Menu 5 Audio Gain Setting
Short press the knob to enter the audio gain setting.
Left + Right Left channel + Right channel
Left Left channel
Right Right channel
Turn the knob to select the audio channel setting, short press the knob to confirm the
audio channel setting.
Turn the knob to adjust the audio channel gain in real time. For best sound quality,
try adjusting the L and R levels to full without OVER. If you want to set mute, adjust
to MUTE. Short press the knob to exit the audio gain setting. And return to menu 5
audio gain setting.

Menu 6 External Modulation Gain Setting
Short press the knob to set the external modulation gain.
Turn the knob to adjust the external modulation gain in real time. If you want to set
mute, adjust to MUTE. Short press the knob to exit the external modulation gain
setting. And return to Menu 6 External Modulation Gain Setting.
Menu 7 network settings
Network option detected not installed. Short press the knob to exit.
Menu 8 exit the menu
Short press the knob to exit the menu and return to the main interface.
System sleep
Long press the knob in the main menu page to sleep the system, short press the
knob to exit the system hibernation.
System alarm prompts

Warning: V.S.W.R standing wave high! Please check the antenna and cable
connection.
Warning: the temperature inside the machine is high! (More than 70 ℃) Please keep
the room clean and does not exceed 40 ℃.