Watermark AUT-DT1 User manual

INSTALLTION FOR
DECK MOUNT AUTOMATIC FAUCET
Rev. 9/19
P a g e | 1
AUT-DT1
AUT-DTM2
AUT-DP3
AUT-DPM4
AUTOMATIC TOUCH ON/OFF
AUTOMATIC METERED TOUCH
AUTOMATIC TOUCHFREE
AUTOMATIC METERED TOUCHFREE
Features:
•Can be used with most Watermark deck mount spouts and finishes
•No visible sensor –turns the spout itself into the sensor
•Battery operated –no need for hardwiring
•Safety timeout so water doesn’t run indefinitely (DT1 and DP3 only)
•Metered option to satisfy local codes for public bathrooms
•No temperature control –water should be pre-tempered
Specifications:
1. Working water pressure: 20 PSI to 85 PSI
2. Working water temperature: 45°F to 120°F
3. Working environmental temperature: 35°F to 100°F
4. Flow Rate: 1.2 GPM lavatory, 1.75 GPM kitchen
5. IP55 water and dust protection
6. 6V CR-P2 lithium battery (included)
7. 12 second metering cycle (DTM2 and DPM4 only) provides 0.24 gallons per cycle
8. Shipping weight (lbs.): 10
9. Shipping dimension (in.): 29 x 12 x 4
Note:
•DO NOT USE PLUMBER’S PUTTY ON ANY OF THE BRASS COMPONENTS
This will cause the finish to tarnish and void the warranty. A non-corrosive Alkoxy Silicone is
recommended.
•DURING SWEATING OF LINES DO NOT OVERHEAT CASTING
Overheating may cause damage to internal mechanism and void the manufacturer’s warranty as well
as increase the risk of scalding.
•COPPER ADAPTORS MAY BE REQUIRED TO COMPLETE YOUR INSTALLATION
•Not for use with metallic sinks or counters.
Diagram A - Dimensions

INSTALLTION FOR
DECK MOUNT AUTOMATIC FAUCET
Rev. 9/19
P a g e | 2
Diagram B –Parts Checklist
#
Description
Qty.
1
Spout Assembly
1
2
Solenoid Valve
1
3
Solenoid Bracket
1
4
Electrical Box
1
5
Supply Hose
1
6
Spout Hose
1
7
Sensor Washer L
1
8
Sensor Washer S
1
9
Battery
1
10
Wood Screw
4
11
Drywall Anchor
4
12
Wall Clip
5
Installation
1. Flush the lines of all dirt and debris.
Note: Failure to completely flush the lines will cause valve failure and will void the manufacturer’s
warranty.
2. Close water supply.
3. Assemble Spout Assembly (1) with Sensor Washer (7 or 8) onto deck as shown in Diagram C.
Diagram C –Spout Assemblies
Type I
Type II
Type III
Type IV
Type V
#
Description
#
Description
#
Description
7
Sensor Washer L
20
Mounting Nut
29
Lock Nut
8
Sensor Washer S
21
Mounting Rubber Washer
30
Adapter Gasket
13
Spout
22
Mounting Washer
31
Adapter
14
Deck Gasket
23
Mounting Rubber Washer
32
Lock Nut
15
Mounting Washer
24
Mounting Washer
33
Mounting Rubber Washer
16
Lock Nut
25
Mounting Nut
34
Mounting Washer
17
Base Ring
26
Tee
35
Lock Nut
18
Mounting Rubber Washer
27
Tee Gasket
36
Tee Gasket

INSTALLTION FOR
DECK MOUNT AUTOMATIC FAUCET
Rev. 9/19
P a g e | 3
19
Mounting Washer
28
Tee Washer
37
Tee
Note: Refer to Diagrams A, B and D for Steps 4 –7.
4. Position Solenoid Bracket (3) on the wall so Solenoid Inlet (38)is within 12” of premixed water supply
and Solenoid Outlet (39)is within 12” of Spout Inlet (40 or 41). Secure with 2 Wood Screws (10).
Drywall Anchors (11) may be used if securing to drywall.
5. Slide Solenoid Valve (2) into Solenoid Bracket (3). Solenoid should be oriented with inlet on bottom
and outlet on right.
6. Connect Supply Hose (5) to the premixed water supply and to Solenoid Inlet (38).
7. Connect Spout Assembly (1) to Solenoid Valve (2):
a. For spout Types I & IV, connect Spout Hose (6) to Spout Inlet (40)and to Solenoid Outlet
(39).
b. For Spout Types II, III & V, connect Spout Inlet (41)to Solenoid Outlet (39).
Diagram D –Solenoid Connection
#
Description
Types I & IV
Types II, III & V
1
Spout Assembly
2
Solenoid Valve
5
Supply Hose
6
Spout Hose
38
Solenoid Inlet
39
Solenoid Outlet
40
Spout Inlet (Types I & IV)
41
Spout Inlet (Types II, III & V)

INSTALLTION FOR
DECK MOUNT AUTOMATIC FAUCET
Rev. 9/19
P a g e | 4
Note: Refer to Diagrams B and E for Steps 8 –12.
8. Position Electrical Box (4) on the wall so the top is within 12” of the Sensor Washer (7 or 8) and
within 28” of the Solenoid Wire Connector (42)and secure with 2 Wood Screws (10). Drywall
Anchors (11) may be used if securing to drywall.
9. Connect Sensor Wire (43) to Sensor Washer (7 or 8) and Solenoid Wire (44)to Solenoid Wire
Connector (42).
Note: Sensor Washer (7 or 8) may be bent to accommodate Sensor Wire (43).
10. Route Sensor Wire (43) and Solenoid Wire (44) so they do not come in contact with each other, with
the hoses or with any metal. Wall Clips (12) can be used to assist with wire routing.
11. Loosen 4 screws on front of Electrical Box (4) to remove front cover. Insert Battery (9) into Electrical
Box (4) (+ to +).
12. Red LED (45)will light and initial calibration will begin. After about 5 seconds, Red LED (45)turns off
indicating initial calibration is complete. Replace front cover and tighten screws.
Note: Do not touch the faucet during initial calibration. If faucet is touched, remove battery and
return to Step 11.
13. Open water supply and activate faucet so water runs through Spout (13). Check all connections for
leaks.
14. Activate faucet 10 times for final calibration:
a. For DT1, touch Spout (13)to turn on. Remove hand and allow to run for 10 seconds. Touch
again to turn off. Wait 10 seconds before next activation.
b. For DTM2, touch Spout (13)to turn on. Remove hand and allow to run until it turns off
automatically, about 12 seconds. Wait 10 seconds before next activation.
c. For DP3, move hand near Spout (13)to turn on and leave hand near Spout (13)to allow to
run for 10 seconds. Remove hand to turn off. Wait 10 seconds before next activation.
d. For DPM4, move hand near Spout (13)to turn on. Remove hand and allow to run until it turns
off automatically, about 12 seconds. Wait 10 seconds before next activation.
Note: Sensor continuously learns environment as it is used. It may take up to a week of regular use to
fully calibrate.
Diagram E –Sensor Connection
#
Description
4
Electrical Box
7/8
Sensor Washer
13
Spout
42
Solenoid Wire Connector
43
Sensor Wire
44
Solenoid Wire
45
Red LED/White Button
Cleaning
1. To clean the spout, press once on White Button (45) to enter cleaning mode for 30 seconds. Red LED
(45) will begin flashing twice repeatedly.
2. During this time, spout may be cleaned without water turning on by touch or proximity.
3. When cleaning mode ends, Red LED (45) will stop flashing and operation will return to normal.

INSTALLTION FOR
DECK MOUNT AUTOMATIC FAUCET
Rev. 9/19
P a g e | 5
Troubleshooting
Red LED Code
Meaning
Remedy
Solid Light
Calibration
Wait for light to turn off. Do not touch faucet until light turns off.
1 Flash
Battery level is low
Replace battery (type CR-P2)
2 Flashes
Cleaning mode or safety
timeout is activated
Wait for light to stop flashing
3 Flashes
Bad connection
Check installation. Make sure sensor wire and solenoid wire are
not touching each other or any metal. Make sure sink and
counter are not metallic. Remove and replace battery, wait for
Red LED to turn off and follow Step 12 above.
Malfunction
Cause
Remedy
Faucet does not
turn on
Sensor stop
Check Electrical Box for flashing Red LED. Follow instructions above.
Water supply is off
Turn water supply on.
Faucet turns on
by itself
Sensitivity too high
Adjust sensitivity. Press and hold the White Button until Red LED is
permanently lit, about 10 seconds. When finger is removed, Red
LED will light in a series of flashes to indicate sensitivity level. 1
flash is the lowest and 5 flashes is the highest. Press the white
button 1 time for each level to be changed. When desired level is
reached, wait for series of flashes from Red LED to confirm level.
Note: Level should be adjusted 1 step at a time and tested.
Faucet functions
intermittently
Calibration not
complete
Follow Step 12 above. It may take up to one week of regular use for
sensor to fully learn environment.
Sensitivity too low
Adjust sensitivity. Press and hold the White Button until Red LED is
permanently lit, about 10 seconds. When finger is removed, Red
LED will light in a series of flashes to indicate sensitivity level. 1
flash is the lowest and 5 flashes is the highest. Press the white
button 1 time for each level to be changed. When desired level is
reached, wait for series of flashes from Red LED to confirm level.
Note: Level should be adjusted 1 step at a time and tested.
Bad connection
Check installation. Make sure sensor wire and solenoid wire are not
touching each other or any metal. Make sure sink and counter are
not metallic. Remove and replace battery, wait for Red LED to turn
off and follow Step 12 above.
Faucet does not
turn off
Sensitivity too high
Adjust sensitivity. Press and hold the White Button until Red LED is
permanently lit, about 10 seconds. When finger is removed, Red
LED will light in a series of flashes to indicate sensitivity level. 1
flash is the lowest and 5 flashes is the highest. Press the white
button 1 time for each level to be changed. When desired level is
reached, wait for series of flashes from Red LED to confirm level.
Note: Level should be adjusted 1 step at a time and tested.
Bad connection
Check installation. Make sure sensor wire and solenoid wire are not
touching each other or any metal. Make sure sink and counter are
not metallic. Remove and replace battery, wait for Red LED to turn
off and follow Step 12 above.
For technical support, please call 718-257-2800