Watermark MPU7 User manual

MPU7 Pop-Up Lavatory Drain with Overflow
350 Dewitt Avenue, Brooklyn, NY 11207 USA T 718.257.2800 F 718.257.2144 www.watermark-designs.com Page 1
Parts Breakdown and Dimensions
ITEM NO.
DESCRIPTION
QTY.
1
Plug
1
2
Eyehook Nut
1
3
Eyehook
1
4
Collar
1
5
Gasket
1
6
Body Washer
2
7
Locknut
1
8
Body
1
9
Tail
1
10
Pivot Washer
2
11
Pivot Arm
1
12
Pivot Nut
1
13
Strap
1
14
Wingnut
1
15
Pivot Clip
1

MPU7 Pop-Up Lavatory Drain with Overflow
350 Dewitt Avenue, Brooklyn, NY 11207 USA T 718.257.2800 F 718.257.2144 www.watermark-designs.com Page 2
STEPS
1. Remove the plug
from the body.
2. Unscrew the
collar.
3. Apply silicon around
the top of the drain
hole.
4. Push the
gasket down to
the body
washer.

MPU7 Pop-Up Lavatory Drain with Overflow
350 Dewitt Avenue, Brooklyn, NY 11207 USA T 718.257.2800 F 718.257.2144 www.watermark-designs.com Page 3
5. Put the body into
the drain hole through
the bottom of the sink
and screw the collar
back onto the body.
Make sure to push the
collar onto the silicon.
Tighten the locknut
such that it pushes the
gasket up to the
bottom of the sink. Do
not overtighten the
nut.
6. Unscrew the
tail from the
body and apply
Teflon tape to
the threads of
the tail. Thread
the tail back
onto the body.
7. Feed the plug into
the body and align it
with the logo as
desired. Remove the
plug and loosen the
eyehook and adjust
the length so that it
will accept the pivot
arm. Carefully tighten
the eyehook nut such
that the eyehook
keeps its orientation.
8. Remove the
pivot nut to
access the pivot
washer, then
remove the
pivot washer
from the pivot
nut.

MPU7 Pop-Up Lavatory Drain with Overflow
350 Dewitt Avenue, Brooklyn, NY 11207 USA T 718.257.2800 F 718.257.2144 www.watermark-designs.com Page 4
9. Remove the pivot
clip form the pivot
arm, then feed the
outer pivot washer
onto the pivot arm
up to the pivot ball.
10. Insert the short
end of the pivot
arm into the body
and make sure the
arm goes through
the hook in the
eyehook. Secure
the pivot nut onto
the body. Make
sure not to
overtighten to
prevent damage to
the pivot washers.
11.Put one end of
the clip onto the
pivot arm. Slide the
strap onto the pivot
arm at the desired
height so it can
attach to the lift
rod. Secure the
other end of the
pivot clip onto the
pivot arm.
12. Insert lift rod
into the top of the
strap and tighten
the wingnut.
13. Connect the drain to the trap and check for leaks.
IMPORTANT INSTALLATION INFORMATION
•USE TEFLON TAPE OR PIPE SEALANT FOR THREADED CONNECTIONS
•DO NOT USE PLUMBER’S PUTTY ON ANY OF THE BRASS COMPONENTS
This will cause the finish to tarnish. A non-corrosive Alkoxy Silicone is recommended.
•DRAINS ARE ONLY UNDER WARRANTY FOR MECHANICAL FAILURE, NOT FOR FINISH DEFECTS
For technical support, please call 718-257-2800