WaterTech INF-SEN1 User manual

INSTALLATION &
OPERATION MANUAL
MODEL: INF-GUARD1 MODEL: INF-SEN1

INFINITY SENTINEL & GUARDIAN
PRODUCT FEATURES & PRECAUTIONS
SENTINEL Addresses:
Sediment
Volatile Organic Compounds (VOC’s)
Trihalomethane
Chlorine Taste & Odor
PRECAUTIONS
Filter is only to be used with cold water.
The contaminants or other substances removed or reduced by this water filter are not necessarily in
all users’ water.
System has been designed to be used on municipally treated water sources. Do not use with water that is
microbiologically unsafe or of unknown water quality without adequate disinfection before
or after the system.
Filter usage must comply with all state and local laws and regulations.
Manufactured from NSF/ANSI standard 61 and California Prop 65 Compliant certified coconut shell carbon
and raw materials.
65
65
65
65
65
MODEL: INF-SEN1
MODEL: INF-GUARD1
GUARDIAN Addresses:
Sediment
Volatile Organic Compounds (VOC’s)
Trihalomethane
Chlorine Taste & Odor
Chloramines
Pharmaceuiticals

INSTALLATION OF INFINITY
WHERE TO INSTALL 1
CITY WATER
INLET WATER
METER
SERVICE
SERVICE
WELL
INLET
RELIEF VALVE
MUST BE
INSTALLED
PRESSURE
TANK
PUMP
WELL WATER
CITY WATER

INSTALLATION OF INFINITY
PRODUCTS & PARTS DIAGRAM
1
3
2
4
7
TEFLON TAPE THREADS
Do Not Overtighten
9
6
PARTS
1. Filter housing
(10-00-001)
2. Bottom Inlet/Outlet cap assembly
(10-00-002)
3. Vertical elbow
(10-00-003)
4. 3/8” PEX Drain valve assembly
with shut-off
(10-00-004)
6. Bypass manifold
(10-00-006)
7. Straight or 90-degree Angled In/Out
1” MNPT plumbing connectors
(10-00-007)
9. Umbrella Cap
(10-00-009)
10. Top Cap
(10-00-010)
11. Retaining Ring
(10-00-011)
12. Replacement Filter
(INF-SEN1-FX)
OR
(INF-GUARD1-FX)
DRAIN VALVE
IMPORTANT:
Bypass Orientation
INLET OUTLET
Flow direction arrows on bypass are
incorrect for this filter application.
Plumb unit opposite of arrows.
6
10
11
The system and installation must comply with state and local laws and regulations.
Plumbing the filtration system assembly: The inlet and outlet of the filtration housing are
1” Threaded MNPT connections.
**No Use of Extra lubricants, unapproved sealants, and use of tools. Use of tools other
than hand tighten only parts, voids warranty.
Please allow 3 feet of open space above the system for replacement cartridges.
System to be supplied only with cold water.
12
2

INSTALLATION OF INFINITY
SIMPLE ASSEMBLY INSTRUCTIONS
NOTE: Additional parts box inside filter housing tank.
STEP 1
Connect #3 to #2 on the bottom of the Filter Housing #1.
HAND TIGHTEN ONLY
STEP 6
Connect 3/8” PEX Plumbing to drain.
NOT PROVIDED
STEP 4OPTION B
Use #7 (90-degree Angled In/Out 1” MNPT) for
connecting your plumbing to the system.
HAND TIGHTEN ONLY
STEP 5
Install part #4 into #3 using the threaded
connection & Teflon®tape.
HAND TIGHTEN ONLY
STEP 4OPTION A
Use #7 (Straight In/Out 1” MNPT) for
connecting your plumbing to the system.
HAND TIGHTEN ONLY
STEP 2
Connect #6 Bypass to #5
HAND TIGHTEN ONLY
TEFLON TAPE THREADS
Do Not Overtighten
DRAIN VALVE
2 3

INSTALLATION OF INFINITY
FILTER CARTRIDGE INSTALLATION
STEP 1
Push down the top cap with both hands.
STEP 4
Look down into the tank assembly, and you should see
a small opening centered in the bottom of the tank.
STEP 7
Press down on the filter cartridge so that the double O-ring
seal moves into place within the bottom, center opening.
STEP 10
Pull up on the Top Cap to seat o-rings.
STEP 2
Remove the retaining ring by carefully grasping the handle
and pulling inward, then upward. The retaining ring should
slide completely out of the groove.
STEP 5
Remove packaging from filter cartridge, then place the filter
cartridge into the tank with the double O-ring facing down.
STEP 8
Reposition the Top Cap into its original location.
STEP 11
Place Umbrella Cap on top of system.
STEP 3
Remove the Top Cap from the housing assembly by pulling
the cap out of the top of the tank, by lifting up on the top
handles. Place removed Top Cap on a clean and dry surface,
free of debris, so no contamination of the o-ring occurs.
STEP 6
Position the cartridge so that it is aligned
with the bottom, center opening.
STEP 9
Reattach the top tank Snap Ring.
STEP 12
Run water through system for 10 minutes before use.
10
4

FILTER CARTRIDGE
REPLACEMENT
NOTE: Due to unknown water quality and water usage, it is
recommended to replace filter annually for a household of 4 people.
4 1
SENTINEL
Filter Replacement
Part Number:
INF-SEN1-FX
GUARDIAN
Filter Replacement
Part Numbers:
INF-GUARD1-FX

FILTER CARTRIDGE
REPLACEMENT
STEP 1
Turn off the water supply to the system by shutting off the
inlet and outlet valves on the bypass.
STEP 3
Depressurize the system by pushing down on the red
depressurization button on the top cap of the system.
Keep the button pushed down until all the air or water
pressure is completely released.
STEP 6
Remove the top cap of the system by lifting
up on the top handles.
STEP 9
Look down into the tank assembly, and you should see
a small opening centered in the bottom of the tank.
STEP 2
Install a 3/8” PEX tubing hose to the provided
John Guest®fitting and shut-off that connects to the
inlet side of the filtration system. Run the hose to a
floor drain or bucket, and use to drain sediment or
to aid in filter removal during change-out.
STEP 4
Push down the top cap with both hands to unseat the
retaining ring.
STEP 7
Remove old filter and discard.
STEP 10
Remove packaging from the new filter cartridge and place
into the tank with the double O-ring facing down.
STEP 5
Remove the retaining ring by carefully grasping the handle
and pulling inward, then upward. The retaining ring should
slide completely out of the groove.
STEP 8
Open the John Guest®fitting shut-off, and
flush out the bottom.
STEP 11
Position the filter cartridge so that it is aligned
with the bottom, center opening.
NO TOOLS
REQUIRED 2

FILTER CARTRIDGE
REPLACEMENT
STEP 12
Press down on the filter cartridge so that the double O-ring
seal moves into place within the bottom, center opening.
STEP 15
Pull up on the Top Cap to seat o-rings.
STEP 18
Relieve the system of air in the tank as the system fills with
water, by pushing down on the red depressurization button
on the top cap of the system. Keep the button pushed down
until all the air pressure is completely released, and water
comes out of the red depressurization button.
STEP 21
Check for leaks.
STEP 13
Reposition the Top Cap into its original location.
STEP 16
(If completed Step 2, then…) Close the
John Guest®fitting and shut-off.
STEP 19
Release the red depressurization button.
STEP 22
Run water through system for 10 minutes before use.
STEP 14
Reattach the top tank Snap Ring.
STEP 17
Turn the water supply on, opening the inlet
and outlet valves on the bypass.
STEP 20
Replace the Umbrella cap to the top of the system.
10
NO TOOLS
REQUIRED 32

WATER FILTER SYSTEMS
NAME AND
PART NUMBER
SIZE &
MICRON RATING
CHLORINE/CHLORAMINE
TASTE AND ODOR REDUCTION CAPACITY (*) PRESSURE DROP SPEC
Infinity Sentinel
INF-SEN1 8” x 40”, 3.0 Nominal 3 micron rated filter to treat >250,000 gallons (946,353 Liters) of water @ 15 gpm (56.78 LPM) with greater than 90% reduction, estimated capacity using 2ppm of free chlorine. 5 psid @ 15 GPM
Infinity Guardian
INF-GUARD1 8” x 40”, 3.0 Nominal 3 micron Chloramine rated filter to treat >50,000 gallons (189,271 Liters) of water @ 7 gpm (26.50 LPM) with greater than 85% reduction, estimated capacity. 5 psid @ 15 GPM
*Claims are not performance tested by IAPMO or NSF. Performance claims are based on independent laboratory and manufacturer’s internal test data.
Actual performance is dependent on influent water quality, flow rates, system design and application. Results may vary.
This pressure vessel is tested and certified
by NSF International against NSF/ANSI
Standard 44 and 61 for materials and
structural integrity requirements
SPECIFICATIONS
IMPORTANT
DO NOT USE extra lubricants, unapproved sealants and tools to
tighten hand tightened only parts. Use of tools other than hand
tighten only parts voids warranty. Flush the system and change the
lter as suggested. The contaminants or other substances removed
or reduced by this water lter are not necessarily in all users’ water.
Filter Replacement Operating Instructions: New cartridges must
be ushed for a minimum of 10 minutes prior to use. System and
installation to comply with state and local laws and regulations.
Do not use with water that is microbiologically unsafe or unknown
quality without adequate disinfection before or after the system.
Manufactured from NSF/ANSI standard 61 and California Prop 65
Compliant certied coconut shell carbon and raw materials.