WE-EF FLA441 LED User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Wall Luminaire Surface Mounted and
Street and Area Lighting Luminaire
FLA441 LED
FLA461 LED
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.

1
Wall Luminaire Surface Mounted and
Street and Area Lighting Luminaire
FLA441
FLA461
)/$:  ,3&ODVV,WDů&
)/$:  ,3&ODVV,WDů&
)/$:  ,3&ODVV,WDů&
)/$: ,3&ODVV,WDů&
385 295
260
145
410530
350
200

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
Attention: The housing Hcontaining the LED light
source is factory-sealed and does not need to be
opened during installation.
Installation Procedure
1) Switch off mains electrical supply.
2) Remove gear box cover Bby loosening screws C.
3) Check that rating shown on luminaire label conforms
with mains electrical supply.
4) Feed mains supply cable Kthrough cable gland G
(Fig. I), while attaching luminaire Dto mounting
accessory.
5) Secure luminaire by tightening sealnuts Eevenly
with tool L(17 mm ring spanner not supplied by
WE-EF).
Attention: Ensure sealnuts ESURYLGHGDUHƂWWHG
as shown with gasketed surface towards pole or
mounting bracket. Do not substitute this fastener.
6) Connect mains supply cable Kleads, and control
lines where applicable,to respective terminals in
terminal connector F:
a) ON/OFF or WE-EF Control Advanced (L = Phase,
N = Neutral, = Earthing)
b) WE-EF Control Basic (L = Phase, N = Neutral,
= Earthing, Ls = Switching Phase)
c)9'$/, orWE-EF Control Dynamic (L=Phase,
N = Neutral, = Earthing, DA/DA = DALI control
OLQH'' 9
control line).
7) Tighten cable gland G.
 Reposition gear box cover Band retighten screws C.

4
Mounting Accessories
8QLYHUVDOPRXQWLQJƃDQJH D/D1
80) IRU)/$ 310-9110   
80) IRU)/$ 310-9109   
)DFLOLWDWHVLQVWDOODWLRQWRƃDWYHUWLFDODQGKRUL]RQWDOVXUIDFHV
Planted root – Galvanised steel.
(69 IRU)/$ 300-9100
(69 IRU)/$ 300-0824
3URYLGHVLQJURXQGVHFWLRQIRUXQLYHUVDOPRXQWLQJƃDQJHLQODQGVFDSHGDUHDV
6LQJOHFROXPQƂWWHU
(% IRU)/$ 310-9134
'RXEOHFROXPQƂWWHU
(% IRU)/$ 310-9135
6LQJOHFROXPQƂWWHU – Aluminium/wood.
(% IRU)/$ 310-9136
'RXEOHFROXPQƂWWHU– Aluminium/wood.
(% IRU)/$ 310-9137
ESV
UMF
EB1/EB2
EB1/EB2
(aluminium/wood)

5
Fig. I. Feed mains supply cable through cable gland

www.we-ef.com
72::(()
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.
WE-EF LEUCHTEN
Germany
7HO
)D[
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
)D[
[e-mail]
WE-EF HELVETICA
6ZLW]HUODQG
Tel [phone]
Fax [phone]
LQIRVZLW]HUODQG#ZHHIFRP






WE-EF LIGHTING
Thailand
7HO
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
7HO
)D[
[e-mail]
WE-EF LIGHTING
United States of America
Tel 
Fax 
[e-mail]

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Planted Root
ESV4
ESV2
ESV6

2
Planted Root
ESV4 300-0461
ESV4 300-0586
ESV4 300-0464
ESV4 300-0459
Suitability
1. KTX234
2. KTY234
3. ZFY230
4. GRY224
5. Short post
Suitability
1. XRY334
2. XRZ334
3. RRY334
4. RRZ334
Suitability
1. CFY259
2. GRY234
3. RRY324
4. RRZ324
5. XRY324
6. XRZ324
Suitability
1. QSI254

3
Planted Root
ESV2 300-9115
ESV6 300-0824
ESV6 300-0457
Suitability
1. PSY414/424
Suitability
1. AML-C
2. FLA461
Suitability
1. LTM440
2. LTM444
3. AMW-C
4. AMF-C
5. AMF-S
6. AML-C
240
200
600

4
Installation Instruction
1) Note: It is the responsibility to installer to
ensure the suitability of the ESV planted root
for any local or national structural requirements
for installation, and that planted root is suitable
IRUVLWHVSHFLƂFFRQGLWLRQV
Instructions are a guideline for installation to
these requirements and provide detail for
installation orientation and mounting details.
4) For ESV2 please orientate planted root as
shown (base plate is parallel to the pathway).
For this installation, use 30 mm long M12
bolts supplied.
2) Please note, ESV4 and ESV6 must be
orientated correctly for different products.
In both instances conduit entry can be rotated
to match cable routing.
When the ESV is being installed for following
products: KTY234/KTX234/ZFY230/CFY259/
FLA461, please orientate the planted root
as shown (base plate is at an angle of 45°
to the pathway). For this installation,
use the 40 mm long M8 bolts supplied.
3) For all other product that use ESV4 please
orientate planted root as shown (base plate is
parallel to the pathway). For this installation,
use 25 mm long M8 bolts supplied.

5
 2ULHQWDWH(69DVUHTXLUHGDQGƂWHOHFWULFDO
connections/conduit.
5) For all other product that use ESV6 please
orientate planted root as shown (base plate
is parallel to the pathway). For this installation,
use 40 mm long M16 bolts supplie.
7) Place the ESV in the form work for concrete
pad, ensuring orientation, position and levels
are correct. Ensure all openings on ESV are
blanked off, including mounting plate hole.
8) Fit the nominated bolts through mounting
ƃDQJH(QVXUHVHYHUDOWKUHDGVIHHGWKURXJK
the plate and tape off top and bottom. Bolts are
inserted to protect threads off plate and need to
EHUHPRYHGIRUƂWWLQJLQVWDOODWLRQDIWHUVHWWLQJ
the ESV.

6
9) Pour concrete to desired level depending on
requirement of soil, paver or concrete. Ensure
WKDWIRUDQ\LQVWDOODWLRQPRXQWLQJƃDQJHPXVWEH
ƃXVKRUKLJKHUWKDQVXUURXQGLQJVXUIDFHOHYHO
$IWHUFRQFUHWHKDVFXUHGIRUVSHFLƂHGWLPH
UHPRYHEODQNLQJDQGEROWV,QVWDOOƂWWLQJ
(as per luminaire instructions) onto mounting
ƃDQJH
Concrete
Paver
Soil

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
TO9257W0420 © WE-EF 2020
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.