WE-EF AFL100 Series User manual

Surge Protection
This product features built-in surge protection circuitry in compliance
with applicable standards.
For comprehensive protection of a luminaire installation against lightning
and electrical surges, it is essential to cover mains supply and data input
lines at the distribution board level, by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation. Also, disconnect luminaires
before operating high-power devices such as, for example, electrical
arc welders.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Post Mounted Luminaires
AFL100 series
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained
in this document for details.

1
Post Mounted Luminaires
IP66. IK08 [AFL120], IK09 [AFL130]. Class I, II. Ta= 25°C
Tool required
Torx 20, 45 5 mm Allen key
Weight kg
for AFL120 max. 6.95
for AFL130 max. 8.60
Windage area m2
for AFL120 max. 0.146
for AFL130 max. 0.191
Windage area m2
for AFL120 max. 0.146
for AFL130 max. 0.191
Mounting height 3 – 8 m
Installation: horizontal, light output downwards
AFL120
AFL130
ø 9 – 14 mm 1 – 2.5 mm2
602
37
65
191.5
653
37
65
191.
5
683
111
733
11
1
250
ø 89
300
ø 89

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried
out by a suitably qualied and trained professional.
Warning: Do not open luminaire while mains supply is switched on.
Caution: Risk of electric shock!
Installation
The product must be installed and maintained by a suitably qualied professional in compliance
with latest building/construction and/or electrical regulations and relevant legislation.
Warning: Switch o mains electrical supply prior to installing and connecting the luminaire.
Caution: Risk of electric shock!
Notice: If the luminaire is modied by anybody other than the original manufacturer, then the warranty will
no longer be valid and shall become the full responsibility of the modifying person/organisation. Claims
based on defects attributable to improper installation and/or application, and the consequences thereof,
are excluded.
Attention: The luminaire is factory-sealed and does not need to be opened during installation.
The installation on site must comply with local and/or national health and safety regulations.

3
B
M
M
I
J
B
Post top and Side entry
Attachment Mcan be mounted vertically or horizontally. To change position loosen fasteners J,
rotate by 180° and refasten.
For vertical mounting, attachment can be set at 0° or 2.5° by loosening screws J. For horizontal
mounting, attachment can be set at 0°, 2.5°, 5°, 7.5°, 10°, 12.5°, and 15°.
Mounting Position
D = 60 mm
Mounting Position
D = 42 mm
L
B
K
M
adaptor.
the fasteners B M10x10 must be replaced with the fasteners B M10x20 supplied with the
Attach adaptor K with the fasteners L to M. See below for position. When using adaptor,
42 mm.
Using adaptor K(Part No.: 102-0392), diameter can be reduced from 76 mm to 60 mm or
Adaptor (to be ordered separately)

4
Installation Procedure
2) Pull the connecting cable through the pole. Place the luminaire on top of the pole and tighten
fasteners B, tightening to a torque of 10 Nm.
Side entry Post top
ø 40-60 x 100*
B
ø 76 x 100
B
Switch o and isolate mains electrical supply.1)
10 Nm
* ø 60 x 100 adaptor Kis required.

5
E
DALI (L = Phase, N = Neutral,
= Earthing, DA/DA = DALI control line)
c)
BASIC (L1 = Phase 1, L2 = Phase 2,N = Neutral,
= Earthing)
b)
ON/OFF (L = Phase, N = Neutral,
= Earthing)
a)
base of the pole:
Trim mains cable E to the desired length and connect the leads to their respective terminals at the 3)
Instructions.
remote SPD behind the door at the base of the pole as per the provided SPD Installation
Unless ordered with an internal SPD, the flex must be connected to the terminals of the provided

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[email protected]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[email protected]
WE-EF SWITZERLAND
Switzerland
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]
TO9280W0223 © WE-EF 2023
Technical specifications are
subject to change.