WE-EF PSY414 LED User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Bollard
PSY414 LED
PSY424 LED
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
Installation tools
Mounting hardware used on this product
includes fasteners with hexalobular socket
heads (ISO 10664). Installation requires the
use of matching tools.

1
Bollard
PSY414 PSY424
IP66, IK10, Class I, ta = 40°C
Weight kg
for PSY414 13.3
for PSY424 16.1
Accessories:
Planted root – Galvanised steel. kg
ESV2 for PSY414/424 300-9115 3.8
ESV2
190
800
180
100
90
ø 14.5
75
180
260
1000
180
100
90
ø 14.5
75
180

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
by a suitably qualiƂed and trained professional.
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a
suitably qualiƂed professional in compliance with latest
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice: If the luminaire is modiƂed by anybody other
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.

4
Installation Procedure
It is recommended to incorporate the optional planted root to ensure maximum stability.
1) Switch off mains electrical supply.
4) Lift tabs Hand remove terminal box cover C
as shown.
2) Remove sleeve Afrom post B.
3) Pull cable through center-hole and screw ƃange
plate Ewith M12 bolts/nuts to ground. Ensure
proper orientation of terminal box. An optional
planted root is available.
Note: Planted root installation instruction is
available at the end of this document.

5
6) Pull cable D(and second cable for through wir-
ing, if required) through membrane spout(s) F
and terminate in terminal block G. Lock cable(s)
with strain relief(s).
7) Return terminal box cover Cand push until
tabs Hengage with pins.
5) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
PSY424 220-240V/50-60 Hz
114-XXXX SOE XXXXXXX
LED 4000K 18W item no. XXX
08/18 IP66
8) Place sleeve A over post Bwith sticker I
pointing up as shown.

6
10)Remove countersunk screws Jfrom head Kwith
Torx 25 tool.
9) Engage sleeve Ainto ƃange plate E
(good and bad engagement).
12)PlaceheadKoversleeve Aand checkfor
alignment.
ƃXVK
orientation tab
11)Hold head Kunder arm. Grab socket L, connect
and tighten with plug M. Use orientation tabs
as shown.

7
13)Tighten M6 Torx 30 recessed screws Nto 6 Nm. 14)Return countersunk screws Jinto head and
tighten.

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
info.asiapaciƂ[e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
TO9245W0219 © WE-EF 2019
Technical speciƂcations are
subject to change.

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Planted Root
ESV4
ESV2