WE-EF FLB141 1 LED User manual

Surge Protection
This product features built-in surge protection circuitry in compliance
with applicable standards.
For comprehensive protection of a luminaire installation against lightning
and electrical surges,it is essential to cover mains supply and data input
lines at the distribution board level,by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation.Also,disconnect luminaires
before operating high-power devices such as, for example,electrical
arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
WE-EF LIGHTING
Installation and Maintenance
Instructions
Floodlight
FLB141 #1 LED

1
Floodlight
FLB141 #1
IP66, IK08. Class I. ta = 40°C
Weight lb
for FLB141 #1 LED 6.83
Windage area ft²
for FLB141 #1 LED 0.409
Orientation: all directions
Mounting Accessories
)ODWVXUIDFHĥWWHU
SF-FLD1 for FLB141 #1 145-9535
&ROXPQĥWWHU
CF-FLD1 for FLB141 #1 145-9536

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces,no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried
RXWE\DVXLWDEO\TXDOLĥHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a VXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and relevant legislation.
Warning:6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWRLQVWDOOLQJDQGFRQQHFWLQJWKHOXPLQDLUH
Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\RWKHUWKDQWKHRULJLQDOPDQXIDFWXUHUWKHQWKHZDUUDQW\ZLOO
no longer be valid and shall become the full responsibility of the modifying person/organisation.
Claims based on defects attributable to improper installation and/or application, and the consequences
thereof, are excluded.
The installation on site must comply with local and/or national health and safety regulations.

4
 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\
Installation Procedure
,QVWDOODWLRQŅ)ODWVXUIDFHĥWWHU
3) Feed cable Afrom luminaire Bthrough pivot and
 KROHRIĦDWVXUIDFHĥWWHUC.
 'HWHUPLQHSRVLWLRQVIRUĥ[LQJVFUHZVD.
Drill relevant holes Eand insert nylon plugs.
Insert and tighten screws D.
Warning: Ensure not to damage any electrical
cable, water pipe or other items drilling holes.
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
FLB141-LED 120-277V / 60Hz
161-XXXX SOE XXXXXXX
LED 3000K 18W item no.XXX
07/18 IP66

5
5) Loosen screws F6OLGHVOLSĥWWHURYHUSLYRW
while pulling cable Athrough hole.
8) Loosen screw G. Aim luminaire in desired
direction and tighten screw G.
6) Turn luminaire towards object to be
LOOXPLQDWHG(QVXUHVOLSĥWWHULVSURSHUO\
seated on pivot,then tighten screws F.
7) Connect cable Awith mains supply cable.
a) ON/OFF (L = Phase,N = Neutral,
= Earthing)
b) 0-10 V (L = Phase,N = Neutral,
= Earthing,D–/D+ = 0-10 V control line).
G

6
 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\
,QVWDOODWLRQ&ROXPQĥWWHU
Suitable for column diameter Ť2.99 in.
6HUYLFHGRRURQFROXPQKDVWREHSURYLGHGIRUFDEOHWHUPLQDWLRQPD[LPXPIWIURPFROXPQĥWWHUPRXQWLQJSRVL-
tion).
3) Drill screw holes Aand cable entry hole Bon
column. Ensure cable entry hole BKDVVXĩFLHQW
diameter to feed cable from luminaire.
 6HWDQGĥ[FROXPQĥWWHUCin position.Insert
and tighten screws D.
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
FLB141-LED 120-277V / 60Hz
161-XXXX SOE XXXXXXX
LED 3000K 18W item no.XXX
07/18 IP66

7
5) Loosen screws F. Feed cable Dfrom luminaire
Ethrough pivot and cable entry hole B.
Connect luminaire EZLWKFROXPQĥWWHUCby
VOLGLQJVOLSĥWWHURYHUSLYRW
8) Loosen screw G. Aim luminaire in desired
direction and tighten screw G.
6) Turn luminaire Etowards object to be
LOOXPLQDWHG(QVXUHVOLSĥWWHULVSURSHUO\
seated on pivot,then tighten screws F.
7) Connect cable Dwith mains supply cable.
a) ON/OFF (L = Phase,N = Neutral,
= Earthing)
b) 0-10 V/DALI (L = Phase,N = Neutral,
= Earthing,D–/D+ = 0-10 V control line).

www.we-ef.com
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]
TO9250W0522 © WE-EF 2022
Technical specifications are
subject to change.