WE-EF LTM444 User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Light column
LTM440-FT
LTM444
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.

1
IP55, IK09, Class I, ta = 40°C
Light column
LTM440-FT LTM444
494

2
Light Source
LED
Maintenance
Apart from cleaning the outside of the luminaire, no special maintenance is necessary.
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
Installation Procedure
It is recommended to incorporate the optional WE-EF
planted root to ensure maximum stability.
1) Switch off mains electrical supply.
2) Check that rating shownonluminairelabelconforms
with mains electrical supply.
3) A suitable recess to be provided for the planted
root A. Ensure that a solid foundation as well as
VXIƂFLHQWPDLQVFDEOHOHQJWKDUHSURYLGHG
4) Remove covers Bfrom cast base Cby loosening
screws D.
5) Set luminaire in position and secure by inserting
and tightening bolts I.
6) Place luminaire head Hover post P, insert plug G
into socket Kand tighten screws Jevenly.
7) Loosen screw Nuntil door Mcan be opened and
removed.
8) Loosen screw Qand remove cover Rof cable con-
necting box L.
9) Connect mains cable Fto terminal connector E,
secure it with strain relief Oand place back coverR.
10)Close door Mand tighten screw N.

4

5
Cable connecting box EK70

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
TO9230W0420 © WE-EF 2020
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Planted Root
ESV4
ESV2
ESV6

2
Planted Root
ESV4 300-0461
ESV4 300-0586
ESV2 300-9115
ESV4 300-0464
ESV4 300-0459
ESV6 300-0457
300-0824
Suitability
1. KTX234
2. KTY234-AP
3. ZFY230-AP
4. GRY224-AP
5. Short post
Suitability
1. XRY334-AP
2. XRZ334
3. RRY334-AP
4. RRZ334
Suitability
1. PSY414/424
Suitability
1. CFY259
2. GRY234-AP
3. RRY324-AP
4. RRZ324
5. XRY324-AP
6. XRZ324
Suitability
1. QSI254
Suitability
1. LTM440
2. LTM444
3. AMW-C
4. AMF-C
5. AMF-S
6. AML-C
7. FLA461

3
Installation Instruction
1) Note: It is the responsibility to installer to
ensure the suitability of the ESV planted root
for any local or national structural requirements
for installation, and that planted root is suitable
IRUVLWHVSHFLƂFFRQGLWLRQV
Instructions are a guideline for installation to
these requirements and provide detail for
installation orientation and mounting details.
4) For ESV2 please orientate planted root as
shown (base plate is parallel to the pathway).
For this installation, use 30 mm long M12
bolts supplied.
2) Please note, ESV4 must be orientated correctly
for different products. In both instances conduit
entry can be rotated to match cable routing.
When the ESV is being installed for following
products: KTY234/KTX234/ZFY230/ CFY259,
please orientate the planted root as shown
(base plate is 45° to the pathway).
For this installation, use the 40 mm long M8
bolts supplied.
3) For all other product that use ESV4 please
orientate planted root as shown (base plate is
parallel to the pathway). For this installation,
use 25 mm long M8 bolts supplied.