Weber mt VPR 700 Operating instructions

VPR 700 1
1015/englisch/Übersetzung der Original-BetriebsanleitungOriginal
VPR 700
Honda GX 160
Weber Maschinentechnik GmbH
Im Boden 5 - 8, 10
57334 Bad Laasphe-Rückershausen / Germany
Telephone [phone] / 398-0
Fax [phone] / 398-101
E-Mail: [email protected]
Web: www.webermt.de
Operating and
Maintenance Manual

2 VPR 700

VPR 700 3
Table of contents
Introduction 4
Safety guidelines 5
Graphic presentation 9
Device description 10
Technical data 11
Activities prior to starting work 13
Starting 14
Compacting 15
Shutting down 15
Maintenance overview 16
Maintenance work 17
Operating uids and ll levels 19
Troubleshooting 19
Storage 20
Contact addresses 23

4 VPR 700
Introduction
This operating and maintenance manual is designed to facilitate familiarization with your soil
compactor, and to enable you to maintain the compactor and use it for its intended purpose.
When complying with the instructions in the operating and maintenance manual you help avoid
hazards, reduce repair and downtime costs, and increase the reliability and service life of your
compactor.
This operating and maintenance manual must always be available at the implementation site
of the soil compactor.
If necessary you can obtain additional information from your authorized WEBER dealer,
or you can obtain information from one of the contact addresses on the last page.
The valid conformity declaration is enclosed with every machine delivery.
You can obtain information on the assembled Honda gasoline engine and nd a spare-part list for it at
www.honda-engines-eu.com.

VPR 700 5
Safety guidelines
General
All safety instructions must be read and complied with, non-compliance results in
– danger to life and limb of the user
– impairments to the machine or other property.
In addition to the operating manual, the accident-prevention regulations in the country where
the appliance is used must be complied with.
Intended use
The soil compactor should only be used if it is in a technically faultless condition, as intended,
in a safety-conscious and hazard-conscious manner, in compliance with the instructions in the
operating manual. Malfunctions that impair safety must be eliminated without delay.
The VPR soil compactor is designed exclusively for compacting
– paving slabs.
Any other use of the soil compactor is considered to be improper use for which the owner shall
be exclusively responsible. All liability is rejected if damage occurs due to non-compliance with
this provision. This risk is borne solely by the user.
Easily foreseeable misuse
Any use for which the machine is not intended.
Operation
Soil compactors are only permitted to be operated by suitable persons of or above the age
of eighteen. Personnel must be instructed in how to guide the compactor by the owner or by
the owner’s assigned personnel.
The machine operator must comply with trafc regulations. If instructions that affect safety are
given by third parties, then the operator must be authorized to reject these instructions.
Protective equipment
This machine is capable of exceeding the permissible sound level of 80 dB(A). The owner might also
face additional dangers when using the machine. Precautionary action must, therefore, be taken.
Unauthorized persons are forbidden from being in the area of the soil compactor during the
compacting process.
Protective equipment includes:
Hearing protection
Hard hat
Safety shoes
Protective gloves

6 VPR 700
Operation
Prior to starting work the owner of the compactor must be familiar with the work environment.
The work environment includes obstacles in the work and trafc area, the bearing capacity of
the ground, as well as the necessary safeguarding of the construction site in the area adjacent
to public trafc; and it includes compliance with trafc regulations.
The soil compactor should only be operated when the protective xtures are mounted.
The protective xtures must all be in functional condition.
At least once per shift the compactor must be checked for apparent defects. If there are apparent
defects then operation of the compactor must be stopped immediately, and the responsible person
must be informed. Prior to restarting, compactor malfunctions that have occurred must be corrected.
Always maintain adequate clearance to the edges of pits and embankments.
Do not drive at ninety degrees to slopes to prevent the compactor from tipping over.
After work has been concluded secure the compactor in accordance with statutory regulations,
particularly in the area of public trafc surfaces.
Operation under difcult conditions
Never inhale the exhaust gas; it contains carbon monoxide, a colorless and odorless gas that
is extremely hazardous, which, if inhaled even briey, can cause unconsciousness and death.
Therefore, never operate the engines in enclosed areas or in areas that are poorly ventilated
(tunnels, caves, covered pits, etc.).
Exercise particular caution when operating the engine in the vicinity of people and livestock.

VPR 700 7
Maintenance and repair work
Only use original Weber spare parts to ensure reliable and safe operation for maintenance
or repair work.
Hydraulic hose lines must be checked at regular intervals in accordance with standard engineering
practice, or they must be replaced at appropriate intervals, even if no signs of safety-relevant defects
are present.
Adjusting tasks, maintenance tasks, and inspection tasks must be carried out on schedule as
specied in this operating and maintenance manual. These activities should only be executed
by instructed personnel.
For repair, service, or inspection work the engine of the compactor must be safeguarded against
unintentional starting.
All pressurized lines, particularly hydraulic lines and lines of the injection system of the drive motor
must be depressurized before performing maintenance or repair tasks.
For maintenance and repair tasks the compactor must be parked on a level and stable substrate
and must be secured from rolling off or tipping over.
Heavy components and assemblies must be secured to and lifted by hoisting machines that can
bear their weight when they are replaced. Ensure that no hazard is caused by raising components
or assemblies.
Do not position yourself or work under suspended loads.
If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact
with the skin, clean affected skin with suitable cleaning agent without delay.

8 VPR 700
Inspection
Compactors must be inspected in accordance with the corresponding implementation conditions
and operating conditions, as needed; however an inspection to ensure operationally safe status
must be performed by an expert at least once a year. The results of the inspection must be recorded
in writing and must be stored at least until the next inspection.
Cleaning work
Prior to cleaning the compactor with a high-pressure cleaner, protect all accessible energized
switches, cable connections, etc. against water penetration by masking them off.
Cleaning tasks should only be executed in areas that are suitable and have been approved for
this purpose (oil separator amongst others).
Disposal
All operating uids and auxiliary materials must be disposed of in an environmentally-compatible
manner in accordance with country-specic regulations.
Warning against irritants or materials hazardous to health
Warning against a hazardous place
Warning against a suspended load
Wear ear protection
General regulation
Environmental protection
Important information for operating and maintenance personnel is marked by pictograms.
Hard hat
Safety shoes
Protective gloves

VPR 700 9
3
4
2
1
Graphic presentation
Overall view VPR 700
1 Engine
2 Manual guidance rod
3 Engine console
4 Exciter
5 Brake (no image)

10 VPR 700
Device description
The VPR 700 compactor is used for terrace construction and paving applications.
Drive
The unit is powered by an air-cooled Honda gasoline engine.
Force is transferred to the exciter mechanically via a V-belt.
Operation
Start the Honda gasoline engine with the attached reversing starter.
After starting, vibration is switched on via the centrifugal clutch attached to the engine.
The manual guidance rod is used to steer the soil compactor.

VPR 700 11
Technical data
VPR 700
Noise emissions in accordance with 2000/14/EC
Sound pressure level LPA ascertained in accordance
with EN 500, in dB (A) 91
Sound power level LWA ascertained in accordance
with EN ISO 3744 and EN 500, in dB (A) 105
Vibration values
Root-mean-square acceleration value
for hand-arm vibration ascertained in accordance
with EN 500 in m/s² 14,5
In accordance with directive 2006/42/EC,
complying with the vibration values is the
owner’s responsibility.
VPR 700
Weight
Operating weight CECE in kg 175
Dimensions
Overall length (in mm) 1245
Overall width (in mm) 720
Height with folded manual guidance rod (in mm) 970
Length – basic device (in mm) 710
Diameter of rolls (in mm) 96
Drive
Engine manufacturer Honda
Type GX 160
Performance at operating speed in accordance
with ISO 3046-1 (kW) 2.8
Combustion process 4-stroke gasoline
Operating speed (1/min) 3200
Vibration
System Single shaft vibrator
Drive concept Mechanical
Frequency (in Hz) 100
Centrifugal force (in kN) 14

12 VPR 700
2
1
3 4
56
1 Description 2 TYPE
.................................................... ....................................................
3 Serial number 4 Year of construction
.................................................... ....................................................
5 Mass 6 Rated power kW
.................................................... ....................................................

VPR 700 13
1
1
1
Transport
Attach the crane hook to the protective frame (1) and lift the
machine onto the means of transport selected.
Only use lifting machines with a minimum bearing
capacity of 200 kg.
Activities prior to starting work
When transporting the soil compactor on a vehicle,
secure it with suitable restraints.
Do not step under suspended loads.
The correct oil level is between the min. and max. marks.
Checking the engine oil level
Pull the oil dipstick (1) out of the crankcase.
Insert the oil dip stick in the oil ller neck, but do not
screw it in.
Open and remove the gas cap (1), check the level,
if necessary top off to the lower edge of the ller neck
with clean fuel in accordance with the specication.
Check the fuel level
For work at the fuel system, have a suitable re-
extinguishing agent at the ready.
Fire, naked light, and smoking is forbidden!
min.
max.
UPPER LEVEL
LOWER LEVEL

14 VPR 700
1
1
2
1
3
2
Starting
Turn the short-circuit button (1) to the “ON” position.
Bring the gas lever (1) into full-throttle position.
Slide the choke lever (2) to the left (close).
After the engine has warmed up, slide the choke lever to
the right (open).
Open the fuel cock (3).
Slowly tighten the handle (1) of the reversing starter (2) until
resistance is noticeable.
Allow the handle (1) to glide back into the initial position, and
then forcefully and completely pull it through with both hands.

VPR 700 15
1
1
1
1
2
Shutting down
Bring the gas lever (1) into idle position.
Compacting
Bring the gas lever (1) into full-throttle position.
Close the fuel cock (2).
Turn the short-circuit button (1) to the “0” – OFF position.
Only run machine within reach of the manual guidance
rod.
During breaks – even if they are short – the machine
must be shut down.
Parked devices that represent an obstacle must be
safeguarded against through conspicuous measures.
Use the brake (1) to secure the machine.

16 VPR 700
Maintenance overview
The regulations of the engine manufacturer must be complied with in addition to the
above maintenance overview!
Work must be carried out using regulation tools, and the operating and maintenance
manual must be complied with for all work.
All maintenance work: Select a collection vessel that is large enough to prevent oil from
spilling onto the ground. Dispose of waste oil in an environmentally friendly manner
(regulation on waste oils).
Dispose of oils, greases, cloths soaked in oil, and replaced parts with oil on them in an
environmentally friendly manner.
If lubricating oils and fuel come into contact with skin, they can cause skin cancer.
Upon contact with the skin, clean affected skin with suitable cleaning agent without delay.
If accessible during maintenance, check the condition and stability of all screws.
Maintenance interval Maintenance point Maintenance activity
After the rst
25 operating hours
Engine – Change the engine oil
– Re-tighten all accessible
threaded connections
Every 8 operating hours /
daily
Air lter –Clean air lter insert,
check for damage,
replace if necessary
Every 150 operating hours /
every 6 months
Engine – Change the engine oil
Every 150 operating hours /
every year
Vibrator – Change oil
Engine – Adjust valve play
– Clean spark plug/
adjust electrode gap

VPR 700 17
1
1
1
2
Change the engine oil
Remove the oil dip stick (1).
When working in the area of the engine compartment
there is a danger of being burnt!
Remove the oil drain screw (2) and drain oil.
After emptying completely, put in the locking screw (1).
Fill with oil in accordance with specications.
Clean / change air lter cartridge
Unscrew the air lter cover (1).
Remove the air lter insert (1) from the air lter enclosure.
Clean air lter insert as specied by the engine manufacturer
if there is damage or if it is extremely dirty.
Maintenance work
Only drain engine oil when at operating temperature.
Danger of scalding due to hot oil.
If lubricating oils and fuel come into contact with
skin, they can cause skin cancer. Upon contact with
the skin, clean affected skin with suitable cleaning agent
without delay.
Dispose of oils, greases, cloths soaked in oil, and
replaced parts with oil on them in an environmentally
friendly manner.

18 VPR 700
1
1
1
Changing the oil in the exciter
Remove the oil drain / ller screw (1) and drain oil.
Fill with oil as specied in the ll quantity table.
Screw in the oil drain / ller screw.
Checking the V-belt
Remove the V-belt guard (1).
Check the V-belt (1) for cracks, damaged anks, and wear.
If there is excessive wear – replace the V-belt as specied
in the repair manual.
Select a collection vessel that is large enough to pre-
vent oil from spilling on the ground. Dispose of waste
oil in an environmentally friendly manner (regulation on
waste oils).
Wipe up/ off oil slick and oil residue and dispose of fuel-
soaked cleaning cloths in an environmentally responsible
manner.
Make sure the support surfaces at the oil ller / drain
screw and the vibrator housing are clean.

VPR 700 19
Operating uids and ll levels
Troubleshooting
Assembly Operating material Quantity
Summer Winter VPR 700
Quality
Engine
Engine oil SAE 10 W 40
(–10 ~ + 50 °C)
API – CD CE
of SHPD
or CCMC – D2 – D3 – PD1
0.6 l
Fuel tank
Gasoline Unleaded gasoline 3.1 l
Vibrator Engine oil 10 W 40/15 W 40 0.02 l
Fault Possible cause Remedy
Soil compactor
does not start
Operating error Execute the start
process as prescribed
Lack of fuel Check the fuel level
Fuel lter fouled Change the fuel lter
Air lter fouled Clean/ change
air lter cartridge
No vibration /
no forward motion
or insufcient
forward motion
Vibrator V-belt defective Change vibrator V-belt

20 VPR 700
Actions to be taken before long-term storage (longer than a month)
If the machine is to be stored for longer than six months, then contact the Weber service
organization to discuss additional measures.
Entire soil compactor – Clean thoroughly
– Check watertight
– If there are leaks, correct defects
Fuel tank –Empty fuel and ll with clean fuel
up to the lower edge of ller neck
Engine – Check oil level, if necessary
ll to upper oil-level mark
–Check air lter, clean,
replace if necessary
–Check fuel lter,
change if necessary
All bare parts / accelerator /
accelerator control cable /
fastening bolts
–Oil/ grease