WEEDO TINA 2 User manual

1
JIANGSU WIIBOOX TECHNOLOGY CO.,LTD
◆This user manual is for standard TINA 2.
◆Because of software or hardware upgrades and model
differences, new revisions may not be listed in this guide.
3D PRINTER
TINA 2
USER MANUAL

1
Content
1.Application Notices............................................................................................................................................................................... 1
1.1. About the User Manual..............................................................................................................................................................1
1.2. Safety Precautions..................................................................................................................................................................... 1
1.3. 3D printing Filament..................................................................................................................................................................2
1.4. Environment requirements.........................................................................................................................................................2
2. Product Appearance and Introduction.................................................................................................................................................. 3
3.Specification.......................................................................................................................................................................................... 4
4. Unboxing.............................................................................................................................................................................................. 4
5. Accessory List...................................................................................................................................................................................... 5
6.Operation Introduction...........................................................................................................................................................................6
6.1 Connect Power Supply............................................................................................................................................................... 6
6.2 Loading Filament........................................................................................................................................................................6
6.3 Start Printing Test....................................................................................................................................................................... 8
7.Introduction of Interface...................................................................................................................................................................... 11
7.1 Common operation on Interface............................................................................................................................................... 13
7.1.1 Print from SD.................................................................................................................................................................13
7.1.2 Printer Function in Prepare............................................................................................................................................14
7.1.3Printer Function in Control.............................................................................................................................................18
7.2 Parameter setting during printing............................................................................................................................................. 23
7.2.1 Pause print/Stop print.................................................................................................................................................... 23
7.2.2 Adjust temperature of nozzle.........................................................................................................................................25
7.2.3 Adjust the speed of nozzle.............................................................................................................................................25
7.2.4 How to change filament when printing......................................................................................................................... 26
7.2.5 Saving print and off....................................................................................................................................................... 28
8.Software...............................................................................................................................................................................................29
9. APP Printing Introduction.................................................................................................................................................................. 36

1
1.Application Notices
1.1. About the User Manual
This User Manual contains important information on the installation, use, maintenance and other questions frequently raised up
about the 3D printer. Please read this user guide carefully before using this 3D printer. For damages to the 3D printer and other
losses caused by the violation of safety precautions and operational processes given in this User Guide, the user should take all the
responsibilities.
1.2. Safety Precautions
1) Please use the machine under room temperature.The printing temperature of the nozzle should not exceed 230 C. When the
machine is working normally or just finished, do not touch heating parts such as motor, nozzle, etc. to avoid scalding. Children
should use it under the care of their parents.
2) The structure of this 3D printer is very complex; please refer to this user guide for troubleshooting. If the problem still cannot
be solved, please contact our after-sale service. Our company will not offer warranty for printers with unauthorized repair by
the user.
3) There is high voltage within the 3D printer and it is prohibited for non-professionals to disassemble the printer. All the
consequences for violation of this precaution should be the responsibility of the user.
4) Please use the power cord and the USB data cable supplied by our company. For printer failure and other consequences
because of using the third-party power cable or USB data cable, the user should take all the responsibilities.
5) When the 3D printer is connected to the power, please plug the power cord into three-hole flat socket complying with the
international standard. The power cord cannot be forced into a two-hole socket. The ground wire must be connected to the
ground and shall not be suspended. Our company will not be responsible for mechanical failure or other accidents caused by
the disconnection of the ground wire.

2
6) The input voltage of the 3D printer is 100-220V. Please feel free to use it in or outside the mainland China.
7) If unexpected power outages are frequent in your area, please equip the 3D printer with UPS power.
1.3. 3D printing Filament
Please use the printing filament provided by our company for this printer. Printing filament sold at the retail market are different in
specifications and varying in quality; As a result, it is easy to block the printer extruder, damage the extruder and motor. Our
company will not offer warranty for printer failure for using third-party printer consumables.
1.4. Environment requirements
This 3D printer can work properly in an environment from 5 ℃ to 40 ℃. If the ambient temperature is beyond this range, the
quality of the printing products will decline.
If the filaments will not be used for a long time, please store them in a sealed package, and it is especially true for PLA consumables
which will absorb moisture in prolonged exposure to air and affect the quality of finished printing products.

3
2. Product Appearance and Introduction
1.
Operation Knob
2.
LCD Screen
3.
Extruder
4.
Filament Holder
5.
Printing Platform

4
3.Specification
Product Size
215*200*270mm
Product Weight
3kgs
Printing Technology
FDM
Filament
PLA，PLA Pro
Filament Diameter
1.75mm
Nozzle Diameter
0.4mm
Build Volume
100*105*100mm
Printing Software
Willbuilder/Cura
Printing Accuracy
0.1-0.4mm
Model File
STL/OBJ/G-code
Printing Method
TF card/Wi-Fi/W Lan
Leveling Method
Auto-Leveling
4. Unboxing
1) Before using the printer,please remove the fixing clip between the printing extruder and the printing platform.If the fixing
material is not removed, turning on the printer may cause damage to the machine.
2) Remove the fixing clip in the 3D printer.
Precautions
When the printer is repaired during the warranty period, it is recommended that it be packaged and shipped in original packaging.
Therefore, please retain the original packaging material. If you replace it with other package,the printer maybe damaged during
transportation.

5
5. Accessory List
1
USB Cable
2
Power Adaptor
3
Power Cable
4
Glue
5
Platform sticker
6
Hex wrench(1.5mm, 2.0mm, 2.5mm)
7
Phillips Screwdriver
8
Wrench
9
M6 Nozzle
10
TF Card
11
TF Card Reader
12
Filament

6
6.Operation Introduction
6.1 Connect Power Supply
(1) Take out the power cord and transformer from the accessory box.
(2) Connect the power supply to the printer as below photo.
6.2 Loading Filament
(1) Insert one end of the “guide tube” into the pneumatic connector of the extruder at the right side of the printer.

7
(2)
(3)
(2)Take out the filament from the box.
(3)Cut 5mm and make it straight, then insert it into the guide tube from the bottom side of the extruder.

8
6.3 Start Printing Test
(1) Take out the TF card from accessory box and insert it into the slot on the left side of the display screen.
(2) Connect the power and open the power switch.
(3)After above 2 steps, the “Info screen”shown in the right figures appears on the screen.
-Display the main interface after booting
-Click the knob, turn the knob clockwise to select “prepare” and click knob