Weefine Smart focus 1000 User manual

Smart focus 1000
MANUAL
Please read the manual carefully before using the video light
Manual Content
<Instruction>
- Component
- Specifications
- Unpacking
<How to use>
- To install the battery
- Operating Instructions
- Thermal protection
- Battery Level Indicator
- To charge the battery
<Maintenance and Warranty>
- General Maintenance
- Warning
- Warranty
- Troubles Shooting
Component
Specifications
LED
Parameters
Brightness
(Lumen)
Beam Angle
(In water)
Battery
Run time
Depth Rating
LED Life
Material
Oxidation
Size
Weight
white Light: 1pcs LED CREE XP-L-HI 5500K
red light: 2pcs LED CREE XB-D 620nm
Wide Light 60 Degrees
1 x 18650 Li-ion batteries (3400mAh)
Turbo light：70min
100m / 330ft
Over 50000 hours
Aviation aluminum
Hard anodic oxidation
33 (D) x 141.2 (L) mm
200g land (Include the battery)
105g in water (Include the battery)
Li-ion battery ChargerVideo light
O Ring Decorative ringHand ORope
Unpacking
TO install the battery
1.Turn the tail cap counter-clockwise to open.
2.Loading the Li-ion battery into the tail cap, make sure the
polarity battery must match the polarity of the diving light
contacts.
3.Turn the tail cap clockwise to reattach the tail to the head
of the video light.
Operating Instructions
Turn on：Press the Button and hold it down for 1 second,
When the light is turn on it will be in the white light mode
at 100% brightness.
Tail Cap
(LED Light)
Wide Light：1000 Lm
Tail Cap
Battery Level Indicator
Strobe port
Button
Light Head
light clamp
①
② ③

Turn OFF：Press the Button and hold it down for more than
3 seconds.
Switch mode
When the light is on: Press and immediately release the
Button.
Press the button and hold it down for more than 3 seconds.The
SOS mode will be off.
SOS / Rapid Strobe
When the light is off: Press the button and hold it down for 3
seconds.The SOS mode will be on.
Press and immediately release the Button:
Strobe mode
When the light is on: Press the button and hold it down for more
than 1.5 seconds.The strobe mode will be on/off（Indicator
flashing, low power does not have this function）.
Press and immediately release the Button（Switching strobe light）
White light 100％ → White light 50％ → White light 0％
Battery Level Indicator
Blue Light: Battery level is 100% - 80%;
Green Light: Battery level is 80% - 30%;
Red Light: Battery level is 30% - 5%;
Flash Red Light: Battery level is < 5%.
Caution：When the battery level indicator is flash red.
1. Unable to switch the mode and adjust the brightness;
2. Only 20% brightness output;
3. Auto shutdown after 10 minutes
To Charge the battery
1. Insert the battery into the charger as shown in the diagram
below.
2. After the battery is insetred into the charger, plug the
charger into the power source.
When the battery begins to charge the indicator light on
the charger will be red.
When the battery is fully charged the indicator light on
the charger will turn green.
General Maintenance
There two-rings in the tail cap. Use silicone to keep the O-rings
well lubricated. It is important to lubricate the o-rings if the
flashlight has not been used in a long time or if the o-ring is
hard. If the O-ring is damaged, broken or deformed it should be
replaced with the spare.
Note：Do not use a sharp tool to remove the O-rings.
Warning
1.Do not open the tail cap when the video light is in the water.
2.Do not shine the light directly into your eyes or another
person’s eyes.
3.Do not touch the battery and charger with wet hands.
4.Use only the manufacturer’s battery and charger with this
system.
5.If the video light will not be used for a long period of time the
battery should be removed.
Failure to comply with these warning may result in damage
to the video light and will nullify the warranty.
Troubles Shooting
Before returing the video light to the vendor, please try the
following to improve function.
Warranty
We provides a warranty against manufacturer defects for 1
year starting from the date of purchase. Manufacturer defects
occuring within 15 days of the date of purchase will result in an
exchange of product at the vendor. All other manufacturer
defects occuring within 1 year of the purchase will be repaired
at no cost. Proof of purchase is required for warranty support.
The warranty does not cover failures or defects resulting from
misuse (e.g; modification; damage), natural disasters, or battery
issues, including incorrect battery installation.
Symptom Solution
The video light
does not work
Indicator light is
green when the
battery begins
charging
Internal Leakage
Water
Check the battery to make sure
that it is inserted in the correct
direction
Check the battery is charged
Check the tail cap is tight
Check the battery to make sure
that it is inserted into the charger
in the correct direction and that
the battery has good contact with
the charging terminal.
Check the O Rings in the tail
cap to make sure that they are
not broken and that there is no
debris which might
18650
Thermal protection
When being used at a temperature higher than 50~55°C
and the temperature protection function will be on, and the
brightness change 20%. When the temperature is lower than 40
°C, the temperature protection function will be off, and the
brightness is restored.
Whilt light:100％ Whilt light:50％ Whilt light:25％
Red light:100％
Red light:0％ Red light:50％
SOS Rapid Strobe
④ ⑤
⑥ ⑦

Smart focus 1000
MANUAL
规格
LED参数
亮度（流明）
发光角度(水中)
电量
使用时间
深度等级
LED 寿命
材质
氧化
尺寸
重量
白光: 1pcs LED CREE XP-L-HI 5500K
红光: 2pcs LED CREE XB-D 620nm
散光 60度
1 x 18650 锂电池 (3400mAh)
超亮：70min
100m / 330ft
大于 50000 小时
航空铝合金
硬质阳极氧化
直径33mm x 长度141.2 mm
200g 陆地 (含电池)
105g 水中 (含电池)
锂电池 充电器视频灯
O 圈 装饰O圈手绳
包装
电池安装
1、按逆时针方向旋开手电筒尾盖；
2、将一节18650 锂电池装入尾盖，注意电池正负极方向，
按尾盖内的正负极贴纸装入；
3、再将尾盖按顺时针方向旋回灯头上
操作说明
开机：在关机状态下，长按1S开机，进入白光模式,亮度100%；
Tail Cap
(灯头)
散光：1000 流明
尾盖
电源指示灯
引闪口
灯头
灯夹
使用前请详细阅读说明书
目录
<介绍>
- 组件
- 规格
- 包装
<操作>
- 电池安装
- 操作说明
- 电量指示灯
- 温度保护功能
- 电池充电
<维护与保修>
- 一般维护
- 警告
- 质量保证
- 故障解决
组件
开关按钮
①
② ③

关机：在任何模式，任何亮度下，长按键大于3S关机
模式切换
开机状态下: 短按按键
长按左键大于3S关机；
白光 100％ → 白光 50％ → 白光 0％
SOS 模式
关机状态下: 在关机情况下，长按大于3秒，进入SOS模式模式
短按按键:
引闪模式
在开机状态下，长按大于1.5S秒，进入（退出）引闪模式(，进入时白光闪
一次提示，指示灯闪烁，低电无此功能)。
此模式下，短按按键切换引闪光：
电池充电
1．当18650 锂电池需要充电时，如下图先将锂电池装入
充电器，注意正负极不得装反；
2．装好后，将充电器插入电源插座，此时充电器指示灯
会显示红色，表示开始充电；
3．充电完成后，充电器指示灯会显示绿色。
18650
白光：100％ 白光：50％ 白光：25％
红光：100％
红光：0％ 红光：50％
SOS 爆闪
一般维护
尾帽中有两个O圈。 使用硅胶保持O圈润滑良好。 如果视频灯
长时间没有使用润滑O圈是很重要的，或者是O圈硬。 如果O
圈损坏，破损或变形，应该是取而代之的是一个新的O圈。包
括两个备用O圈与您的视频灯。
注意：不要使用锋利的工具去除O圈。
警告
1.当视频灯在水中时，请勿打开尾盖。
2.不要将光直接照射到你的眼睛或另一个人的眼睛
2.请勿用湿手触摸电池和充电器。
4.只能使用制造商的电池和充电器系统。
5.如果视频灯不会长时间使用应取出电池。
不遵守这些警告可能会导致损坏视频灯会使保修失效。
电量指示灯
蓝灯: 电池电量为 100% - 80%;
绿灯: 电池电量为 80% - 30%;
红灯: 电池电量为 30% - 5%;
红灯闪烁: 电池电量为 < 5%。
温度保护功能：
当灯头温度达到50度时，进入温度保护，亮度调整到20%,当温度低
于40度时，退出温度保护，亮度恢复到保护前的亮度。
注意：当红灯闪烁的时候
1.不能切换模式和调整亮度；
2.只有20％的亮度输出；
3.10分钟后将自动关闭。
质量保证
自购买日起1年内，我们对制造商的缺陷提供保修；自购买日期后
15天内发生的制造商缺陷导致卖方产品的交换和所有其他制造商在采购
1年内出现的缺陷将免费维修。购买证明需要保证支持。
保修不包括因使用不当而导致的故障或缺陷（例如：修改；损坏）
，自然灾害，或电池问题，包括不正确的电池安装。
故障解决
如果发现手电筒有故障，请试一试以下的解决方法，再退回销售商检修。
故障现象 解决方法
检查电池是否装反
检查电池是否有电
检查尾盖是否已旋紧
检查电池装入充电器正负极是否正
确，或与充电器弹片接触是否良好
请检查电池装入充电器是否装到位
检查尾盖两个O型圈是否有破损或
有杂物
LED灯不亮
刚充电时
充电器亮绿灯
内部漏水
④ ⑤
⑥ ⑦