WeiderPro 831.14934.0 User manual

Model No. 831.14934.0
Serial No.
Write the serial number in the space
above for reference.
Serial
Decal
•Assembly
• Operation
•Maintenance
•Part List and Drawing
Sears, Roebuck and Co.
Hoffman Estates, IL 60179
WEIGHT SYSTEM EXERCISER
User's Manual

TABLE OF CONTENTS
WARNING DECAL PLACEMENT ............................................................... 2
IMPORTANT PRECAUTIONS .................................................................. 3
BEFORE YOU BEGIN ........................................................................ 4
PART IDENTIFICATION CHART ................................................................ 5
ASSEMBLY ................................................................................ 6
ADJUSTMENT ............................................................................ 15
CABLE DIAGRAM .......................................................................... 17
MAINTENANCE ........................................................................... 18
EXERCISE GUIDELINES .................................................................... 19
PART LIST ............................................................................... 21
EXPLODED DRAWING ...................................................................... 22
ORDERING REPLACEMENT PARTS ................................................... Back Cover
90 DAY FULL WARRANTY ........................................................... Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, call
1=877=992=5999 and request a free replacement decal. Apply the decal in the location shown.
Note: The decal(s) may not be shown at actual size.
User Weight: Max 300 LBS
Weight Crutch: Max 310 LBS
Leg Developer: Max 150 LBS
Weight Carriage: Max 100 LBS
Chest Fly Per Arm: Max 50 LBS
Product may not offer all listed exercises.
•Misuse of this machine may result in serious injury.
•Read user's manual prior to use and follow all warnings
and instructions.
•Do not allow children on or around machine.
,Keep body, clothing, and hair free and clear of
all moving parts.
• Replace label if damaged, illegible, or removed, r t_]
•Maximum user weight: 300 Ibs.
Keep hands and
fingers clear of
this area.
2

iMPORTANT PRECAUTIONS
AILWPa_r_ |_tl| |_,1. " To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your weight system before using your weight sys-
tem. Sears assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
1. it is the responsibility of the owner to ensure 8.
that all users of the weight system are
adequately informed of all precautions.
.Before beginning any exercise program,
consult your physician. This is especially
important for persons over the age of 35 or
persons with pre-existing health problems.
.
Wear appropriate exercise clothes while
exercising; do not wear loose clothes that
could become caught on the weight system.
Always wear athletic shoes for foot protec-
tion while exercising.
Keep hands and feet away from moving
parts.
.
.
.
=
.
Use the weight system only as described in
this manual.
The weight system is intended for home use
only. Do not use the weight system in acom-
mercial, rental, or institutional setting.
Use the weight system only on a level sur-
face. Cover the floor beneath the weight
system to protect the floor.
inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
Keep children under age 12 and pets away
from the weight system at all times.
10.
11.
12.
The weight system is designed to support a
maximum user weight of 300 Ibs. (136 kg).
Do not place more than 100 Ibs. (45 kg) of
weight on each weight carriage. Do not place
more than 310 Ibs. (141 kg) of weight, includ-
ing a barbell, on the bar cradles. Note: A
barbell is not included.
Make sure that the cables remain on the pul-
leys at all times, if the cables bind while you
are exercising, stop immediately and make
sure that the cables are on the pulleys.
Over exercising may result in serious injury
or death, if you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
3

BEFORE YOU BEGIN
Thank you for selecting the versatile WELDER PRO'_
weight system. Whether your goal is to tone your body,
build dramatic muscle size and strength, or improve
your cardiovascular system, the weight system will
help you to achieve the specific results you want.
For your benefit, read this manual carefully before
you use the weight system. If you have questions
after reading this manual, please see the back cover
of this manual. To help us assist you, note the product
model number and serial number before contacting us.
The model number and the location of the serial num-
ber decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Height: 7 ft. 1 in. (216 cm)
Length: 7 ft. 4 in. (224 cm)
Width: 4 ft. 1 in. (125 cm)
Cable Carriage
Swivel
Adjustment Knob
Handle
Adjustment Knob
Bar Cradle
Right Side
Left Side
Weight Tube
Weight Carriage
Note: The terms "right side" and "left side" are
determined relative to a person facing away from the
weight system; they do not correspond to right and
left in the drawings in this manual.
4

PART iDENTiFiCATiON CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. Note: If a part is not in
the hardware kit, check to see if it has been preassembled. Extra parts may be included, if apart is miss-
ing, please call 1=877=992=5999.
M10 Locknut (48)
D
M4 Locknut M4 Washer M10 Washer M10 Curved
(50) (58) (52) Washer (51)
M4 x lOmm M4 x 19mm
Bolt (47) Screw (46)
MIO x 47mm Bolt (43)
MIO x 20mm MIO x 25mm
Screw (38) Screw (53)
M10 x 55mm Bolt (42)
M10 x 65mm Bolt (40) MIO x 65mm Hex Bolt (21)
M10 x 75mm Screw (45)
MIO x 117mm Bolt (41)
5

ASSEMBLY
Assembly requires two persons.
Due to its weight and size, the weight system
should be assembled in the location where it will
be used. Make sure that there is enough clear-
ance to walk around the weight system as you
assemble it.
Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you finish all assembly steps.
Left parts are marked "L" or "Left" and right parts
are marked "R" or "Right."
To identify small parts, see page 5.
in addition to the included tool(s), assembly
requires the following tool(s):
two adjustable wrenches
one Phillips screwdriver
Assembly may be easier if you have a set of
wrenches. To avoid damaging parts, do not use
power tools.
.Go to www.weiderservice.com/registration on
your computer and register your product.
• activates your warranty
• saves you time if you ever need to contact
Customer Care
• allows us to notify you of upgrades and offers
Note: if you do not have Internet access, call
1-877-992-5999 and register your product.
6

2. 2
Insert the Left Base (1) into the Right Base (2)
as shown. Attach the Left Base with four M10
x 65mm Hex Bolts (21), eight M10 Washers
(52), and four M10 Locknuts (48). Do not fully
tighten the Hex Bolts yet.
Next, attach a Bumper (23) to the Right Base (2)
with two M4 x 19mm Screws (46).
Attach the other Bumper (23) to the Left Base
(1) in the same way.
46
23 2 52
52
48
21
,Identify the Right Upright (60) and orient it as
shown.
Attach the Right Upright (60) to the Right Base
(2) with four M10 x 20mm Screws (38) and four
M10 Washers (52). Do not fully tighten the
Screws yet.
Attach the Left Upright (3) to the Left Base (1)
in the same way.
3
60---. 3
1
7

4. Identify the Right Post (4) and orient it as shown.
Attach the Right Post (4) to the Right Base
(2) with two M10 x 55mm Bolts (42), four M10
Washers (52), and two M10 Locknuts (48). Do
not fully tighten the Bolts yet.
Attach the Left Post (55) to the other side of
the weight system in the same way.
4
o
o
o
o
o
o _-4
o
48
52
2
42
55_---
.Insert the two Weight Guides (18) into the sock-
ets in the Bumper (23) on the Right Base (2).
Attach the other two Weight Guides (18) to
the other side of the weight system in the
same way.
5
o
o
o
o
o
o
o
o
18"< --
18_
8

.See the inset drawing. Tighten two Weight
Tubes (57) onto a Weight Carriage (19).
Orient the Weight Carriage (19) as shown and
slide it onto the Weight Guides (18) on the Right
Base (2).
Repeat this step on the other side of the
weight system.
6
io
19_ 18
57
9

.Orient the Left and Right Frames (7, 8) as
shown. Insert the Left Frame partway into the
Right Frame.
Attach the Crossbar (6) to the Left and Right
Frames (7, 8) with four M10 x 117mm Bolts (41),
four M10 Curved Washers (51), and four M10
Locknuts (48). Do not fully tighten the Bolts
yet.
Next, insert the Left Frame (7) fully into the Right
Frame (8). Attach the Left and Right Frames with
four M10 x 65mm Bolts (40), eight M10 Washers
(52), and four M10 Locknuts (48). Do not fully
tighten the Bolts yet.
7 41 48
.Identify the Right Bar Cradle (56) and orient it
as shown. Pull the Adjustment Knob (27) on
the Right Bar Cradle, slide the Right Bar Cradle
downward onto the Right Post (4), and then
release the Adjustment Knob into one of the
adjustment holes in the Right Post.
Attach the Left Bar Cradle (22) to the Left
Post (55) in the same way.
Have a second person hold the Left and Right
Frames (7, 8) near the tops of the Right and Left
Posts (4, 55).
Pull the Adjustment Knob (27) on the indicated
Cable Carriage (28), slide the Cable Carriage
downward onto the Right Post (4), and then
release the Adjustment Knob into one of the
adjustment holes in the Right Post.
Repeat this action on the other side of the
weight system.
8
22
10