Wellav UMH-150 User manual

UMH-150
Integrated Receiver Decoder
User Manual
Wellav Technologies Ltd

UMH 150 Integrated Receiver Decoder User Manual
1
Table of Content
Safety................................................................................................................................ 2
Reference .......................................................................................................................... 3
Features............................................................................................................................. 4
Introduction....................................................................................................................... 5
FRONT PANEL.............................................................................................................5
REAR PANEL ..............................................................................................................5
RF IN AND ASI OUT....................................................................................................6
RF IN AND IPOUT.......................................................................................................7
RF IN AND SDI OUT....................................................................................................7
RF IN AND CVBS OUT................................................................................................8
IPIN AND ASI OUT .....................................................................................................8
Front Panel Control & Operation..................................................................................... 10
INPUT ......................................................................................................................12
Sources...............................................................................................................12
Params................................................................................................................12
OUTPUT...................................................................................................................13
Program Setup ....................................................................................................13
Decoder ..............................................................................................................13
SDI.....................................................................................................................14
Ethernet ..............................................................................................................14
SYSTEM ...................................................................................................................15
Local Setup.........................................................................................................15
Properties............................................................................................................15
Factory Setting....................................................................................................15
STATUS ....................................................................................................................15
Input status .........................................................................................................15
Outputs status .....................................................................................................15
NMS Control & Operation .............................................................................................. 16
LAN PARAMETERS SETTING &CONNECTION ESTABLISHMENT....................................16
Local network setting..........................................................................................16
Connection..........................................................................................................16
NMS MAIN INTERFACE CONFIGURATION ..................................................................18
Troubleshooting .............................................................................................................. 24
Specifications.................................................................................................................. 26
Optional Models.............................................................................................................. 27

UMH 150 Integrated Receiver Decoder User Manual
2
Safety
To avoid electric-shock hazards, do not open the receiver; refer service to qualified
personnel only.
Keep the receiver away from flower vases, tubs, sinks, etc., in order to avoid damaging
the equipment.
Do not expose the receiver in the sunlight. And keep it away from the heat source.
Do not block ventilation holes of the Receiver so that air can circulate freely.
When the abnormal phenomenon occurs, cut off the power immediately.
Do not touch the receiver during thunder. That might create electric shock hazards.
Switch the receiver off whenever it remains out of service for an extended period.
Be sure to turn the receiver off and disconnect the AC power cord before cleaning the
receiver surface. If the surface is dirty, wipe clean with a cloth that has been dipped in
a diluted soap water solution and wrung out thoroughly, and then wipe again with a dry
cloth.
Specifications and functions may be changed for improvement without notice in
advance.

UMH 150 Integrated Receiver Decoder User Manual
3
Reference
Connect DiSEqC 1.0/1.2/2.0
The receiver is designed to be DiSEqC 1.0/1.2/2.0 compatible. This allows multiple
antennas to be connected to the receiver simultaneously. If you have two or more fixed
antennas or LNBs, you can use a DiSEqC 1.0/1.2/2.0 switch.
1. Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connectors
of the DiSEqC switch.
2. Connect the coaxial cable from the second LNB to the LNB 2 or LNB B input
connector of the DiSEqC switch.
3. Do the same for other LNBs.
4. Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch
and the other end of the coaxial cable to the LNB IN socket on the receiver.
Connect a Satellite Antenna
To UMH150 IRD, you can connect either a single satellite antenna directly or through
converter box several antennas or LNB of multi-feed equipment.
You can connect a further IRD with the IRD that has common antenna equipment to
receive satellite signals.
Loop Through
If you wish, you can connect the same LNB to another IRD via the loop through of your
digital receiver decoder. Connect one end of a coaxial cable to the LNB OUT on the IRD
and connect the other end to the LNB IN on your second IRD.

UMH 150 Integrated Receiver Decoder User Manual
4
Features
MPEG-2 Digital & Fully DVB-S ETSI/EN300 421 compliant
Input Frequency 950-2150 MHz, Symbol Rate 2 ~ 45 Ms/s
1 LNB Input (F-Type) and Loop-through IF Signal.
2 DVB Common Interface (CI ) for descrambling most common CA system.
SCPC & MCPC Receivable from C/Ku-Band.
DiSEqC 1.0/1.2/2.0 compatible.
Up to 5000 TV & Radio channels and 2000 transponders programmable
1 ASI transport stream input & 1 ASI output capable of working as TS decoder
IP stream input (optional)
2 DVB Common Interface for descrambling most common CA systems
Broadcasting quality video and audio outputs
VBI teletext handling
Balance audio output (XLR)
BNC-interfaced CVBS output
SDI signal output
IP stream output (optional)
Full control via front panel or Ethernet port
DVB-S2/C/T signal input support (optional)
Automatic recovery for latest system configuration from unexpected power off
Software upgrading via RS232 port or NMS